An Andersen E-Series patio door typically costs $4,000-$10,000 installed for a standard-size, two-panel unit, with custom or multi-panel configurations reaching $15,000 or more. The final price depends on dimensions, panel count, wood interior, exterior finish, glass options, installation conditions, and local labor rates.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Door unit | $2,500 | $4,500 | $9,000+ | Two-panel, custom finish, or larger configurations |
| Installation labor | $1,000 | $2,000 | $4,000+ | Higher for structural changes or difficult access |
| Installed project | $4,000 | $7,000 | $15,000+ | Before unusual repairs, taxes, or extensive trim work |
What an Andersen E-Series patio door costs installed
A standard two-panel E-Series sliding patio door, roughly 6 feet wide by 6 feet 8 inches tall, commonly totals $4,000-$8,000 installed. A wider or taller unit, upgraded glass, custom colors, or a hinged configuration can raise the total to $8,000-$15,000 or more. Large folding and multi-panel assemblies may exceed that range.
For a straightforward replacement, budgeting about $5,500-$8,500 is a reasonable starting point. That estimate assumes a standard opening, a wood interior with an aluminum-clad exterior, ordinary access, and no major framing repair. Regional quotes vary; premium labor markets may run 15%-30% above lower-cost areas.
Assumptions: U.S. pricing, standard residential access, typical custom finish, and no major structural changes.
Where wood, glass, and installation labor enter the quote
An E-Series quote combines a made-to-order door with installation and finishing tasks. The table shows common allowances; exact factory pricing depends on configuration and dealer options.
| Quote item | Low | Average | High | Cost basis |
|---|---|---|---|---|
| Door, frame, and standard hardware | $2,500 | $4,500 | $9,000+ | Per unit; size and configuration drive price |
| Glass and finish upgrades | $200 | $700 | $2,000+ | Per door; specialty glass or finishes |
| Removal and disposal | $150 | $350 | $700 | Existing door and debris |
| Installation and trim | $1,000 | $2,000 | $4,000+ | Opening preparation and fitting |
| Permit or inspection | $0 | $150 | $500 | Where locally required |
Labor and opening work can add as much as the door’s basic hardware price. Installers may charge separately for interior casing, exterior flashing, threshold adjustments, haul-away, and repairs discovered after removal.
How panel count, glass, and opening size change the price
Panel count is a major price driver. A two-panel slider usually costs less than a three- or four-panel system because larger assemblies need more glass, track, hardware, and installation time. Moving from a roughly 6-foot opening to an 8- or 12-foot opening can increase the door-unit price by hundreds or several thousand dollars, depending on design.
Custom sizing, unusual shapes, and nonstandard colors also add cost because E-Series products are made to order. Energy-efficient glass packages, laminated glass, or tempered glass where required can raise the unit price by approximately $200-$1,000 or more. Confirm the exact rough-opening width and height before comparing dealer quotes. Changes to an opening wider than the existing frame may require carpentry and additional permits.
What removal and patio-door installation labor add
A routine replacement often takes a two-person crew about 6-10 hours. Typical labor pricing works out to roughly $75-$125 per worker-hour, although contractors may quote a fixed project charge instead.
Removing a heavy multi-panel door, protecting nearby flooring, correcting a sloped sill, or working on an upper-level opening can extend the job to 10-16 hours. Rot, water damage, or a need to rebuild framing may add $500-$2,500 or more. Ask whether the quote includes flashing, insulation, interior and exterior trim, disposal, and cleanup.
A low installation quote may exclude finish work or repairs, so compare the written scope rather than labor totals alone.
How E-Series pricing compares with Andersen 400 Series
The E-Series offers extensive customization, including wood interiors and a broad selection of exterior colors. That flexibility generally places it above more standardized lines. A comparable Andersen 400 Series patio door may cost roughly $2,000-$5,000 for the unit and $3,500-$7,500 installed, depending on size and options. These ranges are not direct product equivalents; glass, dimensions, and hardware should be matched before comparing.
For a standard opening with limited finish choices, a less customized line may reduce the budget by $1,000-$3,000. The E-Series premium may make sense when a particular wood species, color, or configuration is needed, but optional upgrades should be priced individually.
Three E-Series configurations and sample installed quotes
These examples illustrate typical quote logic, not guaranteed dealer prices. Local labor, tax, exact product specification, and site conditions can change the total.
| Configuration | Door estimate | Labor and extras | Installed total |
|---|---|---|---|
| 6-foot two-panel slider, standard glass | $3,200 | 8 hours; $1,600-$2,200 | $4,800-$5,800 |
| 8-foot two-panel unit, upgraded glass and finish | $5,000-$6,500 | 10 hours; $2,000-$2,800 | $7,000-$9,300 |
| 12-foot multi-panel opening with trim work | $8,000-$12,000 | 14 hours; $3,000-$5,000 | $11,000-$17,000 |
Use these totals as quote-comparison checkpoints, then adjust for the measured opening and written scope.
Which E-Series options can lower the patio-door budget
Keep the existing opening dimensions when possible; widening or raising it can add framing, exterior finish, and inspection expenses. Choose a standard size, common glass package, and a small set of finish options instead of specifying upgrades that do not solve a practical need. A basic configuration can avoid hundreds to more than $1,000 in optional charges.
Request at least three itemized quotes using the same door dimensions, panel layout, glass, finish, removal, and trim scope. Scheduling during a contractor’s less-busy period may improve availability, although product lead times and regional demand vary. Preserving a sound frame and limiting unnecessary opening changes are often the largest controllable savings.