Understanding corrugated metal siding cost per square foot helps homeowners budget accurately. This article breaks down the price, with clear low, average, and high ranges, and identifies the main cost drivers that affect the final bill. The typical total price includes material, installation, and project-specific factors.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Material cost (per sq ft) | $1.50 | $3.50 | $5.00 | Includes basic corrugated panels |
| Installed cost (per sq ft) | $6.50 | $9.50 | $12.00 | Includes labor, fasteners, sealants |
| Total cost (per sq ft installed) | $6.50 | $9.50 | $12.00 | Typical range nationwide |
| Labor hours (typical house) | 6–8 hrs | 8–12 hrs | 12–16 hrs | Smaller jobs vs larger homes |
| Material gauge options | 29–26 ga | 26–24 ga | 24 ga | Thicker gauges cost more but last longer |
Assumptions: Midwest labor rates, standard panel sizes, normal access, standard coating, and typical insulation conditions.
What Buyers Typically Pay For Corrugated Metal Siding
Most projects fall within a per-square-foot installed range of $6.50 to $12.00, depending on material grade and scope. For a standard 2,000 sq ft home, that translates to roughly $13,000 to $24,000 installed. The lowest end reflects thinner gauges, basic coatings, and straightforward installations, while the high end accounts for thicker gauges, premium finishes, complex trims, or limited access.
Cost Components That Make Up the Quote
Pricing breaks into four to six major parts: materials, labor, fasteners and sealants, prep and removal, and sometimes permits or disposal. A compact view shows materials at $1.50–$5.00 per sq ft, labor at $4–$7 per sq ft, with additional costs for corners, flashing, and underlayment if applicable.
| Component | Low | Average | High | Notes |
|---|---|---|---|---|
| Materials | $1.50 | $3.50 | $5.00 | Panels, coatings, color |
| Labor | $4.00 | $6.50 | $7.50 | Installation, fastening |
| Fasteners & Sealant | $0.50 | $1.00 | $2.00 | Screws, rubber gaskets, sealant |
| Removal/Prep | $0.50 | $1.50 | $3.00 | Old siding removal, surface prepping |
| Permits/Inspections | $0 | $0–$500 | $1,000 | Depends on local rules |
| Disposal | $0 | $0–$300 | $600 | Waste hauling |
Assumptions: Standard single-story home, no extensive interior rerouting, access to roofline within reach.
Key Variables That Drive the Final Price
Gauge choice, panel length, and roof slope are the top price determinants. Thicker gauges (24 ga) increase material costs but extend life, longer panels reduce seams but may raise handling costs, and steep or multi-level roofs raise installation time and safety requirements.
Ways to Reduce the Corrugated Siding Cost
Control scope and timing to trim the bill without sacrificing durability. Strategies include choosing standard gauges, limiting custom profiles, planning installation during off-peak periods, and batching multiple exterior projects for contractor efficiency.
Regional Variations in Price by U.S. Region
Prices shift with regional labor norms and material supply chains. The Midwest and South often show lower installed costs than the West Coast or dense urban markets, where both labor and disposal fees tend higher. Expect roughly 10%–25% variance between regions for installed pricing.
Material Type and Gauge Impact on Cost
Material and thickness drive most of the material cost delta. Standard corrugated steel for typical homes uses 26–29 gauge, with aluminum options running higher. A 24 ga panel adds resilience but can push per-square-foot prices upward by 0.50–1.50 dollars on average.
Labor Time and Crew Size for Typical Homes
Labor hours correlate with home size, attic access, and existing framing. A single-story 1,200–1,800 sq ft home might require 8–12 hours with a 2-person crew, while larger two-story homes or complicated fascia can require 16–24 hours with a three-person crew, affecting total cost by several thousand dollars.
Replacement vs New Siding: Scope and Pricing
Replacing existing siding adds disposal and prep, while new installations may omit tear-out costs. If the old material is removed, expect an extra charge of roughly $0.50–$2.00 per sq ft, depending on debris management and access. New installs without removal typically save time and labor costs.