Fascia board installation typically costs $7-$20 per linear foot, with a common total of $1,500-$5,000 for replacing 150-250 linear feet around a house. The final price depends on board material, roofline access, removal of damaged fascia, and local labor rates.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Installed fascia per linear foot | $7 | $13 | $20 | Standard replacement, including labor |
| 150 linear feet | $1,050 | $1,950 | $3,000 | Basic access and limited repairs |
| 250 linear feet | $1,750 | $3,250 | $5,000 | Typical whole-house scope |
| Fascia repair | $250 | $700 | $1,500 | Small damaged areas; extensive rot costs more |
What fascia board installation costs by linear foot
For a straightforward replacement, homeowners often pay $7-$20 per linear foot installed. A 150-linear-foot project may cost about $1,050-$3,000, while a larger 250-linear-foot job may reach $1,750-$5,000. These ranges generally assume standard fascia dimensions, ordinary roof access, and no major rafter or soffit repairs.
Material changes the estimate. Primed wood often falls near $6-$12 per linear foot installed, aluminum-wrapped wood around $8-$15, and PVC or composite fascia roughly $10-$22. Local labor, trim details, and disposal can push a quote beyond these typical ranges. Assumptions: standard residential roofline, U.S. average labor, normal access, and no structural repair.
For budgeting, measure the roofline in linear feet and confirm whether removal and disposal are included.
How lumber, labor, and removal shape the quote
Fascia estimates combine board materials with the work required to remove old trim, install the replacement, and finish edges or joints. The table shows common cost shares for a 200-linear-foot project; actual allocations vary with material and access.
| Quote component | Typical price | What it covers | Cost note |
|---|---|---|---|
| Fascia materials | $400-$1,400 | Wood, PVC, or composite boards | About $2-$7 per linear foot |
| Installation labor | $700-$1,800 | Removal, cutting, fastening, and fitting | About $3.50-$9 per linear foot |
| Equipment and access | $100-$600 | Ladders, staging, or lift rental | More likely on tall or difficult rooflines |
| Removal and disposal | $150-$500 | Old board hauling and dump fees | May be included in labor |
| Paint and finish | $100-$500 | Primer, paint, and sealing | Often extra for unfinished wood |
A written estimate should separate materials, labor, disposal, and finish work so competing bids can be compared accurately.
How roofline length, height, and rot change the price
Longer rooflines increase material and installation time, but small jobs may have a minimum charge that raises the per-foot rate. A contractor may charge $300-$700 for a limited repair even when only 10-20 feet of board need replacement. Projects above 250 linear feet may receive a lower unit price if access and setup are uncomplicated.
Height also matters. One-story work is generally less costly than two-story fascia, which may add 10%-30% for staging, lift use, or slower handling. Damage extending into rafter tails or roof decking can add $200-$1,000 or more, depending on the number of affected areas and carpentry required. Labor estimate formula:
Rot beyond the fascia board is a scope change, not a simple trim replacement, so confirm how hidden damage will be priced.
What regional labor rates mean for fascia replacement
Labor and disposal costs differ by market. In lower-cost rural areas and parts of the Midwest or South, a basic installation may run 5%-15% below national averages. Dense metro areas and high-cost coastal markets can run 15%-30% higher, particularly when parking, permits, or lift access complicate the work.
Weather exposure can influence material selection as well. Humid or coastal locations may favor PVC, composite, or metal-wrapped boards over untreated wood, while cold climates may require careful sealing and paint preparation. Those choices can add $2-$8 per linear foot compared with basic primed lumber. Compare local bids using the same linear footage, material, removal scope, and finish specification.
How many hours a fascia crew may need
A two-person crew may replace 100-150 linear feet in about 1-2 workdays when the roofline is accessible and the existing boards come off cleanly. A 200-250-foot project can take 2-4 days if it involves several corners, multiple stories, painting, or small carpentry repairs. Contractors commonly price the job by the linear foot rather than listing an hourly charge.
For reference, carpenter or exterior-trim labor rates often run $50-$100 per worker-hour, with higher rates in expensive metro markets. A short repair can still cost several hundred dollars because travel, setup, and equipment time do not shrink in proportion to the amount of board replaced. Ask whether the estimate assumes a full crew day, minimum service fee, or separate setup charge.
When fascia repair costs less than replacing every board
Localized damage may be repaired for $250-$700 when only a short section is soft, split, or detached and surrounding wood remains sound. Replacing a longer run is often more practical when damage spans 30-50 feet, paint is failing across the roofline, or several joints have opened. A patch may cost less now but can leave mismatched color or recurring work if moisture remains.
Wood is often the least expensive material upfront, but it needs paint or stain maintenance. Aluminum wrap can reduce repainting while retaining a wood core, and PVC or composite resists rot but usually costs more initially. Choose material based on exposure and maintenance needs, not just the lowest installed price.
Three fascia installation quotes for common house sizes
These examples illustrate how footage and access affect a quote. They assume standard materials, ordinary removal, and no major roof or rafter repairs.
| Project example | Scope | Estimated total | Approximate rate |
|---|---|---|---|
| Small ranch repair | 60 feet, wood, 8 labor hours, easy access | $600-$1,100 | $10-$18 per linear foot |
| Average two-story home | 180 feet, aluminum-wrapped boards, 24 labor hours | $2,000-$3,600 | $11-$20 per linear foot |
| Large home with upgrades | 280 feet, PVC, 40 labor hours, lift access | $4,000-$6,500 | $14-$23 per linear foot |
Compare the same project specifications across bids; a lower total may reflect fewer feet, no paint, or excluded disposal.
Which fascia choices can bring the installation price down
Accurate measurements and a defined replacement area help avoid paying for unnecessary full-perimeter work. If only one elevation is damaged, request a separate price for that run and for replacing all fascia. Scheduling fascia work alongside soffit or gutter repairs may reduce repeat setup charges, provided the trades agree on the sequence.
Keep sound boards where practical, select a standard profile, and avoid premium finishes unless the exposure or maintenance requirements justify them. Homeowners can clear access near the walls and move patio furniture, but roof-edge removal and installation are best left to experienced workers. Request at least three itemized quotes that state board type, linear footage, labor, finish, disposal, and how hidden rot will be billed.