A faucet over the stove, often called a pot filler, typically costs $500-$1,500 installed, with a national midpoint near $900. The price depends mainly on whether a water line is already nearby, wall access, faucet quality, and local plumbing rates.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Installed pot filler | $500 | $900 | $1,500 | Standard faucet and accessible wall |
| Faucet | $100 | $300 | $800 | Price varies by finish and brand |
| New water-line work | $200 | $500 | $1,200 | Depends on route and wall repair |
| Labor | $250 | $450 | $900 | Plumbing labor, excluding major repairs |
What a wall-mounted pot filler usually costs
For a straightforward installation, homeowners commonly pay $500-$1,000 total. This assumes a standard swing-arm faucet, a nearby cold-water supply, ordinary drywall or tile access, and no major cabinetry or electrical changes. A project requiring a long pipe run, finished-wall repairs, or premium brass hardware can reach $1,500-$2,500.
A nearby supply line is the biggest reason a pot filler stays near the lower end of the range. Faucet-only installation or replacement at an existing connection may cost $250-$600, while adding a new branch line often accounts for most of the extra expense. Assumptions: U.S. prices, standard residential kitchen, normal access, and no major code corrections.
How faucet, pipe, and wall work shape the quote
Quotes usually combine the fixture, plumbing labor, connection materials, and any wall or tile repair. Some plumbers include a basic shutoff valve and testing; others list small materials separately. The table shows common installed-job allocations, not guaranteed add-on charges.
| Quote component | Typical range | What changes the charge |
|---|---|---|
| Pot filler faucet | $100-$800 | Finish, brand, two-joint arm, and valve quality |
| Pipe, fittings, valve | $40-$200 | Pipe type, line length, and connection points |
| Plumbing labor | $250-$900 | Access, routing, and local hourly rates |
| Wall or tile repair | $100-$600 | Patch size, tile matching, and finish work |
| Permit or inspection | $0-$250 | Local rules and scope of plumbing changes |
A plumber may charge $75-$150 per hour, with a service minimum of roughly $100-$250. Labor can take 2-4 hours for an accessible connection, but a concealed line route and patching may extend the job to a full day.
Why pipe distance and tile access change the price
Distance from the nearest cold-water line is a practical price driver. A connection within 3-6 feet of an accessible sink or supply may add about $200-$500 in plumbing work. A route longer than 10-15 feet, or one crossing cabinets and finished walls, can add $600-$1,200 because of extra pipe, labor, and repair.
Tile removal and replacement can add $150-$600 or more, especially when matching discontinued tile. Masonry, plaster, stone backsplash, or a wall shared with another room may require slower access and specialized patching. The faucet also needs secure support; adding blocking where the wall is open can be inexpensive, but retrofitting support through finished tile may cost more.
Which faucet price fits the kitchen plumbing
Basic pot fillers generally cost $100-$250 and suit budgets where a simple finish and standard reach are acceptable. Midrange models at $250-$500 offer more finish choices and sturdier joints. Premium or designer fixtures can run $500-$800 or higher, but the higher fixture price does not remove the need for a properly routed, secured water line.
Replacing an existing pot filler with a compatible model is usually less expensive than adding one from scratch. If the current valve, pipe location, and mounting support are sound, installation may fall around $250-$600. Compare the faucet’s reach and folded position with the cooktop dimensions before purchasing; a fixture that cannot reach the largest burner-side pot may not serve its intended purpose.
How labor time differs for new and existing lines
With an exposed or easily accessible supply, a plumber may complete the connection in 2-4 hours. A new line routed through cabinets or an open wall often takes 4-8 hours, excluding later finish repairs. A project involving tile cutting, difficult framing, or a long route may need separate plumbing and repair visits.
Ask whether the estimate includes shutting off and draining the line, mounting the faucet, pressure testing, and cleanup. A written quote should also identify who handles backsplash repair. If a general contractor, plumber, and tile installer are all involved, scheduling and minimum trip charges can add $100-$300 beyond the individual task prices.
Regional plumbing rates can shift the installed total
Urban markets with high labor demand may price a comparable installation 15%-30% above a national midpoint. Smaller cities and rural areas may run 5%-20% below it, although travel charges or limited contractor availability can offset the difference. Coastal metros, including parts of California and the Northeast, tend to have higher hourly rates than many Midwestern and Southern markets.
These are broad comparisons, not local price guarantees. A quote for $1,200 may be reasonable in a high-cost metro if it includes new piping and tile repair, while the same amount could be high for a simple replacement with an existing connection. Compare the stated scope, not only the total.
Permits and backsplash repairs to price before work
Permit rules vary by city and by whether the project extends or alters plumbing. A faucet swap may not require a permit, while installing a new water branch can trigger local requirements or inspection. Budget $0-$250 for permit-related charges where applicable, and ask the contractor to confirm responsibility before work begins.
Removal, disposal, and finish repair are sometimes excluded from plumbing bids. Small drywall patching may cost $100-$250; tile repair or replacement can be $200-$600, depending on access and material match. If the backsplash is being renovated anyway, coordinating the pipe installation with that work may prevent paying twice for opening and finishing the same wall.
Ways to control a pot filler installation budget
Keep the faucet near an existing cold-water branch when the layout allows, and choose a standard-size fixture with readily available parts. Confirm the faucet reach, mounting height, and folded clearance before opening the wall. Avoid paying for a premium finish or decorative features that do not improve fit, durability, or function.
Request itemized estimates from at least two licensed plumbers, separating pipe work, fixture installation, and wall repair. Provide photos of the cooktop wall and nearby sink or supply access so bids use similar assumptions. If a pot filler is not essential, carrying water from the sink costs nothing; if a line already exists, replacing a worn fixture can be a more economical option than relocating or extending plumbing.