The price to replace a GE dishwasher control board varies by model, region, and service details. Typical costs include the control board itself, labor, and any needed diagnostics or parts. This article breaks down the price into concrete ranges and factors that most buyers encounter.
Assumptions: Midwest region, standard 24-inch dishwasher, typical GM/GE part compatibility, standard residual labor, no emergency rush.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Control board (GE/Hotpoint compatibility) | $60 | $120 | $250 | New unit, OEM or OEM-equivalent |
| Labor for board replacement | $100 | $180 | $260 | Typically 1.5–3 hours |
| Diagnostic fee | $40 | $70 | $100 | Applied if no work performed or to confirm fault |
| Travel/Service call | $20 | $50 | $120 | Region and accessibility impact |
| Additional parts (display, harness, connectors) | $20 | $60 | $130 | Depends on kit requirements |
| Tax | $5 | $15 | $25 | Local tax rate |
Ge Dishwasher Control Board Cost Breakdown by Component
Control board hardware typically ranges from $60 to $250 depending on model and whether OEM or aftermarket. Assumptions: standard 24-inch GE dishwasher, common console layouts, line-select type boards.
Labor to install often runs $100 to $260. Most techs take 1.5 to 3 hours, with higher rates in expensive markets or if wiring harness reconfiguration is needed.
Diagnostics and service call can add $40 to $100 if the technician needs to confirm a fault before replacing parts.
What a Typical GE Control Board Quote Looks Like
Most customers see a combined price around $180 to $380 for standard board replacements, with occasional pushes toward $500 in complex cases or high-cost regions. Assumptions: single-family home, standard wiring, no rusted connectors.
In practice, the total project price includes the board, labor, potential harness adapters, and tax. Some quotes present per-piece pricing (board per unit) alongside a flat labor rate, then add diagnostic fees if required.
Regional Variations in GE Board Replacement Pricing
Prices tend to be lowest in rural areas and highest in large metro markets with higher labor rates. Expect averages of $160–$340 in many regions, with $120–$200 for the board itself in budget scenarios and $200–$350 for labor in higher-cost markets. Assumptions: standard travel radius, non-urgent scheduling.
Labor Time Range for Board Replacement on GE Dishwashers
Typical labor duration spans 1.5–3 hours depending on model access, screw types, and harness complexity. Formula: labor hours × hourly rate yields the labor component in dollars, commonly $120–$260 total.
How Model Type Affects the Price Tag
Older GE models may use discontinued boards with limited availability, raising costs to $150–$250 for the board and $120–$300 for labor if specialty adapters are needed. Newer midrange units typically stay around $100–$180 for the board and $100–$240 for labor. Assumptions: model year gap no wider than a decade.
Optional Add-Ons That Change the Final Cost
Wiring harness adapters, display assemblies, or protective housings can add $20–$130. If a diagnostic visit is billed separately, it adds $40–$100. Bundling parts and labor in a single visit often reduces per-item overhead. Assumptions: no flood damage, no corrosion, standard connector types.
Regional Price Comparisons for GE Control Board Jobs
Coastal cities usually trend higher than inland markets due to cost of living, with ranges often extending beyond typical estimates. For the same GE board job, a coastal region might show $210–$430, while a midwestern area shows $160–$320. Assumptions: similar board model family, standard warranty terms.
Strategic Ways to Cut the GE Board Replacement Cost
One practical approach is to confirm that the board is the root cause via diagnostics before replacement. If a non-board issue exists, repair may be cheaper. Choosing OEM-equivalent parts instead of premium boards can also trim the bill. Scheduling during non-peak times may lower labor charges. Assumptions: valid fault code, no hidden corrosion, standard travel radius.
How to Read a GE Control Board Replacement Quote
Look for: board price, labor rate, hours, diagnostic fee, and any required adapters. A clear quote lists components with per-unit prices and a line for tax. Compare items across vendors to ensure you’re not paying for unnecessary parts. Assumptions: itemized quote, no surprise charges.
Real-World Quote Scenarios for GE Dishwashers
Scenario A: 2015 GE model, OEM board, standard harness, Midwest service call. Board $110, Labor $150, Diagnostic $60, Tax $12 → Total around $332. Scenario B: 2020 GE model, aftermarket board, expedited scheduling in coastal market. Board $95, Labor $230, Diagnostics $70, Tax $20 → Total around $415. Scenario C: High-end stainless unit, harness adjustments needed. Board $180, Labor $260, Adapters $70, Tax $28 → Total around $538. Assumptions: single-unit project, standard disposal not included.
What Drives the Final GE Board Price Most
Major cost components are the board itself, labor rate, and regional access. Board availability and model compatibility drive the largest jumps; local labor rates shape the hourly portion.
Mini Cost Summary Table
Estimations vary, but a concise view helps budgeting across regions.
| Cost Driver | Low | Average | High | Notes |
|---|---|---|---|---|
| Board price | $60 | $120 | $250 | OEM or compatible |
| Labor | $100 | $180 | $260 | 1.5–3 hours |
| Diagnostics | $40 | $70 | $100 | Applied if fault confirmed |
| Travel | $20 | $50 | $120 | Region impact |
| Tax | $5 | $15 | $25 | Local rate |
In summary, GE dishwasher control board replacement costs generally fall in the $180–$380 range for typical homeowners, with broader $140–$500 scenarios in high-cost markets or for complex harness work. Accurate quotes hinge on model compatibility, access, and whether OEM parts are required.