GE dishwasher repair typically costs $150-$400, with many standard repairs averaging about $250. The final price depends on the failed part, appliance age and model, labor rates, and whether a service-call fee is charged separately or applied to the repair.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Typical completed repair | $100 | $250 | $600 | Parts and labor; complex repairs may exceed this range |
| Diagnostic or service call | $75 | $100 | $150 | May be credited toward approved work |
| Labor rate | $75/hour | $110/hour | $160/hour | Often subject to a one-hour minimum |
| Common replacement part | $25 | $100 | $350 | Part cost varies widely by model and fault |
What GE dishwasher owners usually pay for a repair
For a standard GE built-in dishwasher with ordinary access, a straightforward repair often totals $150-$300. A control board, circulation pump, or multiple-part repair can bring the bill to $350-$600 or more. Rates tend to be higher in major metro areas and for older or less common models with costly parts.
These estimates assume a technician diagnoses the appliance, installs a compatible replacement part, and tests the cycle. They do not include unusual plumbing or electrical work, cabinet changes, or a second visit caused by a back-ordered part. Assumptions: U.S. residential service, standard access, and no major installation changes.
A practical budget is about $250 for a common repair, plus any service fee that is not credited toward the work.
How parts, diagnosis, and labor appear on the quote
Repair companies may quote a flat repair price or list the service call, labor, and parts separately. Ask whether the diagnostic charge is included in the quoted total, and whether the part has a warranty. The ranges below are typical planning figures, not fixed GE prices.
| Quote component | Low | Average | High | What it covers |
|---|---|---|---|---|
| Diagnostic or trip fee | $75 | $100 | $150 | Visit and fault testing |
| Labor | $75 | $150 | $320 | About 1-2 hours at local rates |
| Part | $25 | $125 | $350 | Valve, latch, pump, sensor, or board |
| Removal or extra work | $0 | $40 | $150 | Haul-away or difficult access, if needed |
| Common total | $150 | $250 | $600 | Typical completed repair range |
Labor alone can add $75-$320, depending on time on site and the technician’s hourly rate.
When diagnosis and labor push the bill higher
A basic door-latch or float-switch replacement may take about 1-1.5 hours, while tracing an intermittent electrical fault or replacing a pump can take 2-3 hours. Typical labor is $75-$160 per hour, but many providers use a minimum charge or flat-rate pricing rather than billing each hour exactly.
Service-call policies matter: a $75-$150 diagnostic fee may be additional, waived, or credited if the repair proceeds. A second visit can add $50-$150 when the correct part is not on the truck. Before approving work, ask for the total price including diagnosis, labor, parts, and return-trip charges.
Confirm the all-in quote before the repair begins, not just the hourly rate or part price.
How model age and failed parts change GE repair prices
The failed component is often the largest variable. A clogged filter or minor door adjustment may cost less than a motor or electronic control replacement. Part availability also differs by model: a common current model may have readily available components, while a discontinued unit can require a special order or a more expensive compatible part.
| Repair type | Typical total | Common price driver |
|---|---|---|
| Door latch or switch | $120-$250 | Part access and door-panel removal |
| Water inlet valve | $150-$300 | Valve price and supply-line access |
| Drain pump | $180-$350 | Model-specific pump and time to access |
| Circulation pump or motor | $250-$500 | Higher-cost assembly and installation time |
| Control board | $250-$600 | Board availability, model, and programming needs |
A unit over 8-10 years old may also have wear in more than one component; fixing one fault does not guarantee another aging part will not fail later. Check the model number before comparing part estimates because GE components are not interchangeable across all dishwashers.
Three GE repair quotes for common household problems
A dishwasher that will not drain might need a pump or a simple obstruction removed. For example, a $90 diagnostic fee, $110 in labor, and a $90 pump part comes to about $290 before any additional disposal charge. If clearing a blockage resolves the issue, the total may be closer to the service fee and a short labor charge.
For a leaking unit with a failed inlet valve, an illustrative quote could include a $95 visit, $120 labor, and a $65 part, totaling $280. A control-board replacement might instead involve a $100 diagnostic fee, $180 labor, and a $220 board, for about $500. Actual totals depend on model, local rates, and whether the diagnostic fee is credited.
Comparing itemized totals makes it easier to spot whether a high quote comes from labor, the part, or added fees.
Repair or replace a GE dishwasher after a major failure
A new dishwasher commonly costs roughly $500-$1,200 for the appliance, with installation often adding $150-$350 when hookups are standard. Premium models, haul-away, new valves, or electrical changes can raise the installed total. Compare that expense with the repair quote, the dishwasher’s age, and its recent repair history.
For a newer unit with a repair under $300, fixing it may be economical if the appliance has otherwise worked reliably. When a dishwasher is 8-10 years old and needs a $400-$600 pump or control board, replacement may be worth pricing, especially if another major repair occurred recently. Judge a costly repair against the full installed replacement price, not the appliance-only sticker price.
Why GE repair prices vary between U.S. regions
Local labor and travel time can shift a quote even when the same part is needed. In dense, high-cost metro markets, service rates may run about 10%-25% above a national midrange; rural areas can also cost more when a technician must travel farther or make a dedicated return visit. Competition and local part availability can narrow or widen the gap.
Request estimates from providers that serve the same ZIP code and ask whether the service fee is included. A low trip charge is not necessarily a lower total if labor or parts are priced separately. Compare complete, written estimates for the same repair scope and warranty terms.
Ways to lower the GE dishwasher repair bill
Have the model number and a clear description of symptoms ready when booking; note error codes, leaks, noises, and whether the unit fills or drains. Check the owner’s manual for safe basic steps such as cleaning the filter, but do not remove electrical panels or work around live wiring. Accurate details can help the technician bring the likely part.
Ask whether diagnosis is credited, whether a replacement part is new or refurbished, and how long parts and labor are covered. If the quote is near the cost of replacement, get a second estimate before approving a major assembly. Avoid replacing a functioning dishwasher solely to obtain an optional feature upgrade.
Controlling the scope and comparing all-in quotes are the most reliable ways to keep repair spending predictable.