A Hampton H15 gas stove may cost about $2,000-$3,500 for the appliance when available, with a typical installed total of $4,000-$6,500. The final price depends on whether the model is new, used, or leftover inventory, plus venting, gas-line work, installation labor, and local permit requirements.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| H15 stove only | $2,000 | $2,750 | $3,500 | Availability and condition can shift the price |
| Venting and fittings | $500 | $1,000 | $1,800 | Depends on vent route and required components |
| Installation labor | $700 | $1,200 | $2,000 | Higher if gas or vent work is extensive |
| Typical installed project | $3,500 | $5,000 | $7,500 | Before unusual repairs or major code upgrades |
Assumptions: U.S. dollars, standard residential installation, normal access, and no major chimney or gas-system repairs.
What a Hampton H15 stove costs before installation
Budget roughly $2,000-$3,500 for the appliance alone, if a dealer can source an H15 in suitable condition. The Hampton H15 is an older Regency gas-stove model, so its price is not as predictable as that of a current product with regular dealer inventory. A new-in-box or dealer-held unit may command more than a used stove, while a private-party listing may cost less but carry no meaningful installation or warranty support.
Before comparing prices, confirm the exact model, fuel type, condition, included logs and trim, and whether the unit has been tested. Ask for the rating plate details and installation manual. Gas appliances must be compatible with the home’s natural-gas or propane supply; conversion parts and approved conversion work can add cost.
A complete installed project often falls around $3,500-$7,500. The lower end assumes an accessible location, a suitable existing gas supply, and a straightforward approved vent route. A project near the high end may need a new gas branch, a longer vent run, wall or roof work, or additional finishing.
How venting, gas work, and labor shape the quote
Venting and site work can rival the appliance price when the stove is not replacing an existing gas unit. A quote should separate the stove, vent parts, gas connection, labor, permit charges, and finishing so the homeowner can see what is driving the total.
| Quote component | Typical range | Pricing basis | What changes the charge |
|---|---|---|---|
| H15 appliance | $2,000-$3,500 | Per stove | Condition, availability, accessories |
| Direct-vent materials | $500-$1,800 | Per vent system | Length, elbows, termination, wall or roof route |
| Gas piping and hookup | $250-$1,000 | Per connection or branch | Pipe distance, access, capacity and fuel type |
| Installation labor | $700-$2,000 | $75-$150 per hour | Crew size, preparation, testing and finish work |
| Permit and inspection | $50-$400 | Per project | Local jurisdiction and scope of work |
Labor may involve setting and leveling the stove, assembling the vent, making the gas connection, checking for leaks, testing ignition and operation, and reviewing safe use. A basic installation may take 6-10 hours of onsite work; complex venting or gas-pipe routing can require more time or a second visit.
Ask whether the quote includes delivery, removal of an old appliance, wall protection, trim, final inspection, and startup. Some installers charge a service or travel minimum of $150-$350 even when the actual work is brief. A low labor figure may exclude vent materials, permit handling, or finish repairs.
Which vent route and gas-line distance change the price?
Venting layout and gas-pipe length are two of the most important H15 installation variables. A short, approved route through an exterior wall can be less expensive than a route that must pass through floors, an attic, or a roof. Each bend, change in direction, or difficult termination can require additional approved components and labor.
For budgeting, a simple wall exit may keep vent materials near $500-$900. A longer route or a roof termination can push vent-system costs toward $1,200-$1,800 or more, particularly if access requires scaffolding or roof work. The installer must use the vent configuration and clearances specified for the exact stove; an existing fireplace chimney is not automatically an acceptable vent.
Gas-line distance also matters. A connection within roughly 10 feet of an adequately sized line may cost about $250-$500. Extending a branch 20-30 feet, opening finished walls, or upgrading an undersized supply can bring the gas-work charge to $700-$1,500. Propane installations may need regulator or tank-side checks in addition to the appliance connection.
Confirm that the proposed location meets the manual’s clearance requirements for combustible materials. A tight corner, mantel, window, or walkway can require moving the stove or changing the vent plan. Such changes affect both labor and finishing, not merely the parts bill.
How condition, fuel type, and included parts affect H15 pricing
Model condition matters especially because the H15 is an older stove and may be sold through limited or secondary-market channels. A dealer-held unit with verified operation, complete documentation, and parts support is not directly comparable with an untested private sale. A lower purchase price can be offset by missing components, service work, or difficulty finding model-specific parts.
Request a written description of whether the price includes the burner, logs, glass, remote or wall control, trim, and any required conversion kit. Missing decorative or operational parts can add several hundred dollars, depending on what is needed and whether it can still be sourced. Do not assume a used stove is ready to install merely because it lights.
Fuel configuration should be verified before purchase. Natural-gas and propane versions may require different setup or approved conversion components. Allow approximately $150-$500 for a straightforward conversion-related parts and service allowance when the manufacturer permits conversion, but confirm compatibility with a qualified installer before committing. An unsupported conversion or appliance with an uncertain history is not a safe cost-saving choice.
Warranty coverage may be limited or unavailable for discontinued stock and used appliances. Ask who handles defects, whether parts are covered, and whether the installation warranty is separate from the appliance warranty. A written answer is more useful than relying on a seller’s general statement that the stove is in good condition.
What homeowners pay in different U.S. markets
Local labor rates and permit practices can move the installed quote by hundreds or more, even when the stove price is unchanged. In lower-cost rural markets, straightforward labor may run about 10%-15% below a national midpoint, while major metro areas and high-cost coastal markets may be 15%-30% higher. These are planning adjustments, not fixed regional tariffs.
A rural installation can still cost more if the nearest qualified gas-stove installer is far away or must make a special trip for startup. Conversely, an urban home may have several competing contractors but stricter building access, parking, inspection, or condo requirements. Obtain local quotes that specify the same vent route and scope before treating regional averages as comparable.
Permit expenses vary by city and county. Some jurisdictions require a mechanical or fuel-gas permit and inspection; others handle a gas appliance under a broader project permit. Budget $50-$400 for ordinary permit and inspection charges, then verify requirements with the local building department or the contractor responsible for the work. Any required code correction is separate from the permit fee.
Winter demand can also affect scheduling. During cold spells, installers may prioritize emergency heating repairs, while fall can bring more competition for appointment slots. Booking ahead may prevent rush charges, but an old stove should not be used or installed without the required safety checks simply to avoid a seasonal price increase.
Three installed H15 estimates for different homes
These examples show how the same stove can produce substantially different totals as installation scope changes. They assume a purchase price within the expected range for a verified unit and standard residential labor; actual quotes depend on the model’s availability and local rules.
| Scenario | Appliance | Work and materials | Estimated total |
|---|---|---|---|
| Existing gas-stove replacement | $2,300 | 6 labor hours at $100 per hour, $500 vent adjustment, $150 permit | $3,550 |
| New exterior-wall installation | $2,750 | 10 labor hours at $115 per hour, $900 venting, $450 gas line, $200 permit | $5,450 |
| Long route with roof termination | $3,300 | 14 labor hours at $135 per hour, $1,650 venting, $900 gas work, $300 permit and finishing | $8,340 |
In the first example, the old appliance location and service connections are reusable, subject to inspection. The second assumes a new through-wall vent and a moderate gas-line extension. The third reflects more involved routing and access; it is a scenario estimate, not a standard surcharge for every roof installation.
Compare line items rather than just the total. If one quote is $1,000 lower, check whether it omits a permit, vent termination, gas-pressure test, removal, or finish repair. Ask each contractor to identify assumptions and list exclusions so the comparison uses the same project scope.
When an H15 replacement or another gas stove costs less
A used H15 can be a bargain only if its condition, parts availability, and installation compatibility are verified before purchase. For a unit priced at $1,200-$2,000, a professional inspection or service allowance of $250-$700 may be sensible, but it does not guarantee that parts are available or that the stove can be installed under current local requirements.
A current small direct-vent gas stove may cost about $2,500-$5,000 for the appliance, with a typical installed total of $4,500-$8,500. That option can provide clearer parts support and a current warranty, though it may exceed the price of an H15 already in good condition. Compare output, dimensions, vent specifications, controls, and service support rather than selecting by purchase price alone.
If an existing H15 is malfunctioning, diagnosis and repair may cost $150-$350 for a service visit, with common parts-and-labor repairs around $250-$900. A control, valve, or unavailable model-specific component can cost more or make replacement more practical. Request a repair estimate that identifies the failed part and whether the work restores safe operation.
Electric supplemental heaters may have a lower purchase cost, commonly $50-$500, but they do not provide the same fuel source or installation characteristics. They can be suitable for occasional room heating, but they are not a direct substitute for every gas-stove use. Compare operating cost and heating needs separately from the initial purchase price.
How to lower the installed Hampton H15 price safely
The most reliable savings come from reducing avoidable scope, not skipping venting, gas, or safety work. Keep the stove near an approved exterior-wall location when practical, and ask the installer whether an existing gas branch and vent opening can be reused after inspection. Reuse may reduce materials and labor, but only if the components are compatible and in acceptable condition.
Get two or three itemized quotes from contractors experienced with gas stoves. Provide the same photos, measurements, fuel type, vent path, and model information to each bidder. Ask for separate figures for appliance, labor, vent materials, gas piping, permits, delivery, and removal; this reveals whether a low quote simply leaves out required work.
Check dealer-held or open-box inventory, but verify the serial number, condition, included parts, return terms, and warranty before paying. A used unit should be inspected by a qualified professional before installation. Avoid buying a stove first and discovering afterward that its vent parts or conversion components are unavailable.
Do simple preparation that does not involve gas or vent disassembly: clear the access route, remove nearby furniture, and confirm delivery access. Avoid optional finish upgrades until the required installation is priced. Keep permits, approved clearances, leak testing, and commissioning in the budget; cutting these items can create safety and resale problems that outweigh any initial savings.