A Husky THD750L tile saw typically costs about $40-$100 used, while an unused older unit may be listed around $100-$180, depending on condition and included parts. Because this 7-inch wet saw is an older model, availability, blade condition, completeness, and local demand matter more than a fixed retail price.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Used THD750L | $30 | $65 | $100 | Working saw; price varies with wear and accessories |
| Unused or boxed older stock | $100 | $140 | $180 | Availability is limited; verify operation and return terms |
| Replacement 7-inch wet saw | $80 | $130 | $200 | New entry-level models; features and capacity vary |
| Replacement blade | $15 | $30 | $50 | Diamond blade price depends on type and quality |
What a working Husky THD750L usually sells for
A realistic target is $50-$80 for a complete, tested used saw. Listings near $30-$45 may involve a worn blade, missing fence, water-tray problems, or no opportunity to test the motor. A clean unit with its original accessories can justify $80-$100, especially where comparable saws are scarce.
The THD750L is a compact 7-inch wet tile saw intended for smaller tile projects, not a substitute for a larger contractor saw. Used prices assume the motor runs, the table and tray are present, and the saw can circulate water. Condition and included parts can change value more than small differences in age.
Assumptions: U.S. local pickup, standard working condition, no shipping, and no major repair needed.
How blade, tray, and motor condition shape the quote
For a used saw, the purchase price is only part of the cost if essential components are missing or worn. The table below shows typical U.S. replacement or repair allowances; availability for an older model can be limited, so compatible parts should be confirmed before purchase.
| Cost item | Typical price | What to check | Budget effect |
|---|---|---|---|
| Diamond blade | $15-$50 | Diameter and arbor compatibility | Replace if chipped, worn, or unsuitable |
| Water tray or pump-related parts | $10-$45 | Cracks, leaks, and water flow | May require improvised or compatible parts |
| Fence or guide pieces | $10-$35 | Included hardware and alignment | Missing pieces can reduce cutting accuracy |
| Motor or electrical repair | $50-$150 | Startup, noise, cord, and switch | Often uneconomical compared with replacement |
A low purchase price can lose its value if repairs push the total near the cost of a new entry-level saw. These are general part and repair allowances, not guaranteed THD750L parts prices.
Why blade size, missing parts, and testing change the price
Condition is the largest price driver. A saw that starts smoothly, cuts without excessive vibration, and delivers steady water flow is worth more than an untested listing. A missing blade or fence can add roughly $15-$50 or $10-$35, respectively, before the saw is ready for use.
Project requirements also matter. A 7-inch saw suits smaller tile and light occasional work; larger or thicker tile may require a different saw with greater cutting capacity. If the job needs repeated long cuts or many tiles, the cost of renting or buying a larger model may be more sensible than modifying a compact saw.
Do not pay a tested-saw price for an untested unit. Ask the seller to run it briefly with water, check for leaks, and show that the table and guide move as expected. A nonrunning unit should be priced as a repair project, not as ready-to-use equipment.
How to keep the THD750L purchase within budget
Compare the complete cost, not just the asking price. A $45 saw missing its blade and guide may cost more to prepare than a $70 complete unit. Confirm what is included, inspect the power cord and tray, and avoid paying extra for accessories that will not fit or be used.
Set a maximum total before negotiating. For ordinary DIY use, a working used saw around $50-$80 can be reasonable; above $100, compare it with a new 7-inch model that includes a warranty. If the motor or water system needs substantial repair, replacement is usually the lower-risk choice.
How long setup and tile cutting add to the job cost
There is no installer labor charge when the saw is used as a DIY tool, but tile work still takes setup, measuring, and cleanup time. A small homeowner project may require 1-2 hours to set up and make a limited number of cuts; larger batches can take several hours depending on layout and tile material.
For paid help, general handyman or tile labor may run about $50-$100 per hour, with minimum service charges commonly around $75-$150. Hiring someone only to make a few cuts can cost more per cut than renting equipment or arranging cuts as part of a broader installation.
Example: Two hours of work at $60-$90 per hour equals $120-$180 in labor, before materials or travel charges.
When a replacement 7-inch saw costs less than repair
A used THD750L is most attractive when it works and includes the tray, guide, and usable blade. If it needs a motor repair estimated at $50-$150, a new basic 7-inch wet saw priced around $80-$200 may offer better value, especially when warranty coverage and readily available parts matter.
Rental can be another option for a one-time project. Depending on the tool and rental market, a small wet saw may cost about $30-$60 per day, plus a deposit or blade charge. Rental makes more sense when the job is short and storage or future use is unlikely; repeated projects can favor buying.
Compare total ownership cost against the number of cuts needed. For an occasional small job, a complete used saw or short rental may be enough. For frequent work or larger tile, compare capacity and support rather than choosing solely by the lowest sticker price.
What to check before paying for an older wet saw
Ask for the exact model number and confirm the saw is the THD750L, since used listings can mix up Husky models. Check that the motor starts, the blade spins without wobble, the tray holds water, and the table is stable. Confirm the blade size and included accessories before agreeing on a price.
Shipping can make an inexpensive listing uneconomical because a wet saw is bulky and may need careful packing. Local pickup allows a basic inspection and avoids freight charges that can add $25-$75 or more. For an untested or incomplete saw, lower the offer to account for both repair risk and missing parts.