A used Husqvarna 137 chainsaw typically costs $80-$180 in the U.S., with a common price near $125 for a running saw in fair-to-good condition. Price depends mainly on starting and cutting condition, included bar and chain, maintenance needs, and local availability; clean refurbished or unused old-stock saws can cost more.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Used saw, sold as-is | $50 | $100 | $150 | May need service or parts |
| Running used saw | $80 | $125 | $180 | Typical private-sale range |
| Serviced or refurbished saw | $150 | $225 | $300 | Condition and warranty vary |
| Bar and chain replacement | $30 | $55 | $90 | Parts only; size and brand matter |
Assumptions: U.S. private-party and small-shop listings; shipping and sales tax are excluded.
Used Husqvarna 137 chainsaw prices by condition
The 137 is an older, discontinued gas chainsaw, so most buyers are comparing used examples rather than current production units. A saw that starts cold, idles steadily, oils the chain, and cuts under load usually falls around $100-$180. An untested or nonrunning unit can be $50-$100, while a clean example recently serviced by a repair shop may reach $180-$300.
For a ready-to-use saw, budget about $125-$180 before tax and any delivery charge. New old stock is uncommon; asking prices may exceed $300, but rarity does not guarantee that seals, fuel lines, or other age-sensitive parts are sound. Confirm that the saw is actually unused and testable before paying a premium.
What the 137 purchase quote includes
Private listings often include only the powerhead, bar, and chain. A shop’s price may include inspection or service, but buyers should ask what was replaced and whether labor is covered. The following ranges are typical planning amounts, not a fixed parts schedule.
| Quote item | Typical price | What changes the charge | Buyer check |
|---|---|---|---|
| Used powerhead with bar and chain | $80-$180 | Starting, compression, wear | Ask for a cold-start test |
| Bar and chain parts | $30-$90 | Bar length and chain type | Verify fit for this saw |
| Shop labor | $75-$125 per hour | Shop minimum and repair scope | Request labor estimate first |
| Common tune-up parts | $15-$60 | Filter, plug, fuel line, filter | Get an itemized parts list |
| Shipping or local delivery | $15-$60 | Distance and carrier | Check packed weight and fees |
Example: 1.5 hours of diagnosis and basic service at $90 per hour adds $135, before parts.
Condition and repair needs that change the price
Working condition matters more than cosmetic wear. A dull chain is a modest expense; poor compression, a damaged starter, carburetor trouble, or an oiling fault can make a low-priced saw uneconomical. A seller’s claim that it “ran last year” is not the same as a current start and cut test.
Subtract likely repairs from the seller’s asking price before comparing it with a tested saw. A basic service may total $60-$150 including parts, while a carburetor or fuel-system repair can reach $100-$250 at a shop. Engine damage can cost more than the saw’s market value. Have a qualified technician inspect a questionable unit if the purchase price is substantial.
Does a 16-inch bar add much to the 137 price?
Bar length and condition can affect value, but a longer bar is not automatically an upgrade. Many used 137 listings have a 14- or 16-inch setup; compatible bar and chain availability should be verified by the saw’s exact specifications. Replacing a worn bar and chain commonly adds $30-$90 for parts, and shop installation may add labor.
For occasional pruning or cutting smaller firewood, a shorter, sharp bar may be more useful than a worn longer setup. If the chain is stretched, damaged, or the bar rails are badly worn, price the correct replacement parts before agreeing to a total. A mismatched bar or chain can create fit and safety problems.
How regional listings shift the asking price
Prices vary with local demand and the supply of used outdoor power equipment. Rural areas with frequent firewood use may have more listings and more price competition, while remote locations can add travel or shipping costs. In higher-cost metro markets, asking prices may run roughly 10%-20% above comparable rural listings; scarce supply can also push prices upward.
Compare completed local sales when possible, not just active asking prices. A $140 listing nearby may be a better deal than a $110 saw that requires a long drive, shipping, or immediate repair. Sales tax, platform fees, and delivery can add roughly 5%-15% to the amount paid, depending on location and buying method.
Three realistic 137 purchase totals
These examples show how condition and service change the out-the-door budget. Actual quotes vary by shop rate, parts availability, and local taxes.
| Scenario | Saw and work | Estimated total |
|---|---|---|
| As-is project | $70 saw plus $100-$200 repair allowance | $170-$270 |
| Running private-sale saw | $125 saw plus $30-$60 chain or maintenance parts | $155-$185 |
| Shop-serviced purchase | $180 saw plus $60-$120 inspection or service | $240-$300 |
Assumptions: No major engine failure, shipping, or sales tax; repair allowance is not a guaranteed shop quote.
When a repair bill outweighs another used saw
A repair is sensible when the engine is healthy and the problem is limited to maintenance items such as a chain, filter, or fuel line. It is less attractive when diagnosis points to low compression, extensive engine damage, or multiple parts unavailable at a reasonable price. Parts support for an older model can vary, so confirm availability before authorizing work.
Compare the complete repair total with the price of a tested replacement, not just the estimate for the first failed part. If repairs approach $150-$250, a buyer may find better value in another inspected used saw or a current entry-level model with a clear parts and warranty path.
Ways to keep a used 137 purchase within budget
Ask for a cold start, idle, chain-brake check, and brief cut test before purchase. Confirm that the chain oil system works and inspect the bar, chain, starter, and fuel lines. A seller who cannot demonstrate operation should price the saw as a repair project rather than as a ready-to-use tool.
Compare at least three local listings with similar condition and included equipment. Negotiate based on specific defects and documented repair estimates, not cosmetic marks alone. Avoid paying extra for accessories that are worn or incompatible, and include travel, tax, and likely service in the total budget.