A Lowe’s 2x6x8 treated board typically costs about $9-$16, with an estimated average near $12.50 before tax. The shelf price varies by store, treatment rating, wood species, and local supply; delivery, cutting, and project labor can raise the total.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| One treated 2x6x8 board | $9 | $12.50 | $16 | Retail estimate; check local store inventory |
| Price per linear foot | $1.13 | $1.56 | $2.00 | Based on an 8-foot board |
| Ten-board purchase | $90 | $125 | $160 | Before tax, delivery, or cutting |
What a Lowe’s 2x6x8 treated board usually costs
The listed dimensions describe a nominal board; the actual size is generally about 1.5 inches by 5.5 inches by 8 feet. At the estimated average of $12.50, the lumber costs about $1.56 per linear foot. Prices can differ between stores and product listings, so the online price for the specific location is the best check before a trip.
Budget roughly $9-$16 per board for the lumber alone. These ranges represent common retail pricing, not a guaranteed current Lowe’s quote. Standard pressure-treated pine is assumed; boards with different treatment labels, grades, or availability may fall outside the range.
Assumptions: U.S. retail pricing, one standard pressure-treated 2x6x8 board, no tax, delivery, or installation.
How lumber, delivery, and labor change the quote
The board’s shelf price is only part of a project budget. A small purchase may require no delivery, while a large order or distant delivery address can add a fee. Installation labor is separate from the lumber price and depends on the job, access, and local contractor rates.
| Quote item | Typical range | Pricing basis | What changes it |
|---|---|---|---|
| Treated board | $9-$16 | Per 8-foot board | Store, grade, treatment, supply |
| Delivery | $0-$100+ | Per order | Distance, order size, service options |
| Cutting | $0-$10 | Per board or order | Store policy and cut complexity |
| Installation labor | $50-$100 | Per hour | Trade, region, and project scope |
| Sales tax | Varies | Local rate | State and local tax rules |
For installed work, labor and delivery may matter more than a few dollars of board-price difference. A rough labor calculation is shown by , with the actual quote also reflecting setup, fasteners, and any removal.
Does treatment grade or board condition change the price?
Yes. Boards intended for ground contact may cost more than lumber labeled for above-ground use, and a higher treatment level is not automatically needed for every project. The required label depends on exposure and the application. Buyers should follow local building requirements and the product label rather than choosing solely by price.
Also inspect each board for bowing, splits, deep checks, and damaged edges. Pressure-treated lumber can be wet and heavier when new; some movement or surface checking can occur as it dries. A straighter board may be worth selecting for visible framing even if it costs slightly more.
Match the treatment label to the exposure before comparing prices. The 8-foot length is convenient for short framing runs, but cutting it down creates waste and may require additional boards for a larger layout.
How project size changes the per-board budget
At the estimated average retail price, 5 boards cost about $62.50, 10 cost about $125, and 20 cost about $250 before tax. At the low and high ends, a 20-board order would run roughly $180-$320. These totals exclude delivery, connectors, fasteners, and installation.
For a basic frame, confirm the board count from the actual layout and account for end cuts and rejected pieces. A project needing many short sections may use lumber inefficiently if every piece is cut from an 8-foot board. A cut list can show whether a longer or shorter stock length reduces waste.
What regional and seasonal pricing can mean
Retail lumber prices can vary by market, store inventory, and transportation costs. As a planning allowance, buyers may see prices around 5%-15% below a broad midpoint in lower-cost supply areas, or 5%-20% above it in higher-cost urban or constrained markets. These are budgeting differences, not fixed regional price rules.
Demand for outdoor building materials can rise in spring and early summer, sometimes limiting selection or changing promotions. Winter availability and pricing depend on local weather and store supply. Comparing the local store price with nearby locations is more useful than relying on a national average.
Use a local store quote for the final budget, especially for multi-board orders. A small per-board difference becomes more noticeable across a deck frame or fence project.
Three sample totals for common board quantities
| Purchase example | Quantity and rate | Lumber total | Possible added expense |
|---|---|---|---|
| Small repair | 2 boards at $9-$16 | $18-$32 | Tax; possible cutting fee |
| Short framing run | 10 boards at $9-$16 | $90-$160 | $0-$100+ delivery if ordered |
| Larger project supply | 20 boards at $9-$16 | $180-$320 | Delivery, fasteners, labor |
These examples use board counts only, not a structural takeoff. A deck, stair, or load-bearing project may require a particular grade, span, spacing, and connector specification. Those requirements can change both the quantity and the acceptable product.
Can a different board size or untreated lumber cost less?
Untreated lumber may have a lower purchase price, but it is not a direct substitute where exposure requires treated material. Painting or sealing does not necessarily meet the same application requirements. For a protected indoor project, untreated lumber may be appropriate if plans and local rules allow it.
A 2x6x10 or 2x6x12 board may reduce joints on longer runs but costs more per board. Compare its price per linear foot and the cut plan rather than comparing sticker prices alone. For short repair pieces, ask whether a smaller quantity or useful offcut is available before buying full boards.
Ways to lower the lumber bill without wasting boards
Measure the project and make a cut list before shopping. Buying only the required treatment type and grade avoids paying for specifications the job does not need. For larger quantities, compare the total cart price, including delivery, rather than the price of one board.
Check current local pricing and stock before traveling, and ask about bulk pricing if the order is substantial. Choose straight boards in person when practical, since a warped piece can create replacement costs or extra cutting waste. Avoid leaving treated lumber exposed to standing water or ground contact beyond its intended use.
The biggest controllable savings usually come from accurate quantities, efficient cuts, and avoiding unnecessary delivery. Keep a modest allowance for waste, but base it on the project layout instead of automatically adding a large surplus.