Maytag washer timer replacement typically costs $250-$500 total, with an average near $350 for a common top-load model and standard access. The final price depends on the washer’s model, whether it uses a mechanical timer or electronic control, local service rates, and whether the part is still available.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Replacement part | $100 | $200 | $350 | Timer or compatible control component |
| Labor and service | $100 | $150 | $250 | Includes typical diagnostic and repair time |
| Total replacement | $200 | $350 | $600 | Higher totals may involve scarce parts or extra repairs |
| Part price per unit | $100 | $200 | $350 | Before shipping or applicable tax |
Assumptions: U.S. service call, standard residential washer, normal access, and no unrelated component failure.
Typical Maytag washer timer prices by repair scope
For a straightforward replacement, homeowners commonly pay $250-$500 including diagnosis, part, and installation. The lower end is more likely when a compatible timer costs about $100-$175 and the repair takes roughly an hour. Older or less common models can require a part costing $250-$350, pushing the total toward $600.
These estimates generally apply to a single washer and do not include major wiring repairs, a second service visit, or replacement of a control board that was initially mistaken for a timer. Before approving work, the customer should ask whether the diagnostic fee is included in the quoted total and whether the replacement part is new, refurbished, or aftermarket.
What the timer repair quote pays for
The part and technician’s time make up most of the bill. A typical quote may divide costs as follows; actual charges vary by model and local labor rates.
| Quote item | Low | Average | High | What it covers |
|---|---|---|---|---|
| Timer or control part | $100 | $200 | $350 | Model-compatible replacement |
| Diagnostic or service fee | $75 | $100 | $150 | Travel and fault testing |
| Installation labor | $75 | $125 | $200 | Removal, wiring, installation, testing |
| Shipping or small supplies | $0 | $20 | $50 | Special order delivery or connectors |
| Typical total | $250 | $350 | $600 | Before unusual repairs or tax |
Some companies apply the diagnostic charge toward the repair; others list it separately. A repair involving 1-2 labor hours at $75-$125 per hour would add about $75-$250 in labor, depending on the billing minimum and whether diagnosis is separate.
Model numbers and timer type can change the estimate
Confirming the exact model number is the most important step before comparing part prices. Maytag washers may use a mechanical timer, an electronic control, or another cycle-control arrangement. A symptom such as stopping mid-cycle does not prove that the timer has failed; a lid switch, wiring fault, drain problem, or control board can produce similar behavior.
Part availability also changes the quote. A commonly stocked timer may cost $100-$200, while a discontinued component for an older model can exceed $250 or require a compatible substitute. A technician may charge extra if the washer needs wiring repair, a connector replacement, or a return visit after a special-order part arrives. Ask for the part number and whether the quote includes a parts warranty.
Ways to reduce the Maytag timer repair bill
Control the scope before agreeing to a replacement. Provide the technician with the full model number and a clear description of the cycle problem so the correct part can be checked before the visit. Ask for an itemized quote that separates diagnosis, part, labor, delivery, and any additional work.
Compare two or three local repair estimates, but check whether each includes the same diagnostic fee and part warranty. If the timer is available from a reliable supplier, ask whether customer-supplied parts are accepted; some companies will not warranty labor on outside parts. Avoid replacing a timer based only on a symptom or an online price listing, since a misdiagnosis can add the cost of an unnecessary component.
How long the timer diagnosis and installation take
A typical on-site replacement takes about 1-2 hours after the technician confirms the fault. Diagnosis may take 30-60 minutes, with additional time for removing the console, transferring wiring, fitting the replacement, and checking multiple cycle settings. A simple repair may be completed in one visit when the part is stocked.
If the correct timer must be ordered, the repair can take several days or longer, depending on supplier inventory and shipping. A second trip may add another service or labor charge, often $50-$150 if it is not included in the original estimate. Confirm in advance whether the quote covers follow-up installation.
When an older washer needs more than a timer
Compare the repair total with the washer’s age and condition, not just the part price. A $250-$400 timer repair can make sense when the washer otherwise works well and has no recurring leaks, spin problems, or costly prior repairs. A quote near $500-$600 deserves closer comparison with the price of a replacement washer, especially if other components are worn.
Replacement may be more practical when the timer is discontinued, the technician finds multiple failures, or a control board and wiring also need attention. Ask the technician to identify the failed component and list any additional repairs separately. A second diagnosis can help distinguish a timer failure from a lower-cost switch, latch, or wiring problem.
Why Maytag timer quotes differ by region
Local labor and travel charges can shift the total even when the part is identical. In many metropolitan areas, service rates and minimum visit fees run about 10%-25% above a national midrange estimate. Rural customers may see a similar increase when a technician must travel farther or make a separate trip for a special-order part.
As a planning range, a standard repair may total $250-$425 in lower-cost markets, $300-$500 in many suburban areas, and $375-$600 in high-cost cities or remote service zones. These are broad comparisons, not fixed regional price lists; model availability and diagnostic policies can outweigh location. Compare the complete installed price rather than an advertised hourly rate alone.
Could the fault be an electronic control instead?
A timer quote should match the washer’s actual cycle-control design. Some Maytag models use electronic controls rather than a traditional mechanical timer, and a control-board replacement can cost roughly $250-$600 installed, depending on board price and labor. A technician should test the washer before recommending either repair.
Ask whether the estimate names the timer or control-board part number and explains the diagnostic result. If the quote changes after testing, request the revised total before work proceeds. That check can prevent paying for a timer that does not fit the model or replacing a board when the problem lies elsewhere.