A used Porter-Cable table saw typically costs $150-$350, while a clean saw with its stand and accessories may reach $400-$500. Price depends mainly on model, working condition, included parts, and local demand; the brand’s saws are discontinued, so most buyers are comparing secondhand listings rather than current factory prices.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Used saw, tested | $150 | $275 | $400 | Common portable 10-inch models |
| Saw with stand and accessories | $225 | $350 | $500 | Value depends on completeness and condition |
| Repair or tune-up | $50 | $150 | $350 | Parts and shop labor vary |
| Replacement blade | $25 | $45 | $90 | Typical 10-inch general-purpose blade |
What a used Porter-Cable table saw usually costs
For the commonly encountered 10-inch portable saws, including the PCB220TS, a reasonable buying range is $150-$400. Around $250-$325 is a practical target for a running saw with its fence, blade guard, and miter gauge. A complete kit with a folding stand, extra blades, and clean accessories can justify a higher asking price, but only if each part is present and functional.
Prices are estimates for private-party sales, not guaranteed sale values. A saw that cannot be tested, has a missing fence, or shows motor trouble should be priced below a comparable working unit. Assumptions: U.S. secondhand market, standard 10-inch portable model, ordinary cosmetic wear, and no major repair required. Most buyers should budget about $250-$350 for a tested saw in usable condition.
Which parts of the used-saw quote add value
A listing price is not just the motor and table. Missing safety parts or a damaged fence can require replacement, while a sound stand and sharp blade make a portable saw more immediately useful. The table below gives typical secondhand values or replacement allowances; replacement parts may be difficult to source for discontinued models.
| Quote item | Typical price range | What to check | Price effect |
|---|---|---|---|
| Saw and motor | $150-$300 | Starts smoothly; no unusual noise | Main value |
| Fence and miter gauge | $25-$100 | Locks square; moves without binding | Missing parts lower value |
| Stand | $40-$120 | Legs, braces, wheels, and latches | Raises value if compatible |
| Blade and guard | $25-$90 | Blade condition; guard completeness | May require replacement |
| Delivery or pickup | $0-$60 | Distance and loading help | Usually negotiable |
A complete, straight fence and intact guard are more valuable than a seller’s claim that the saw was lightly used. Confirm the stand model fits the saw and check whether the price includes the throat plate, anti-kickback pawls, wrench, and manual.
How blade size and condition change the asking price
Model identification matters because Porter-Cable sold different saw configurations and accessories. Check the model plate and confirm the unit is a 10-inch saw before comparing it with similar listings. A clean, tested model with a stand can command $50-$125 more than a bare saw, while a damaged fence or missing guard may reduce its practical value by $40-$100.
Ask the seller to demonstrate startup, blade height adjustment, and bevel adjustment. Listen for bearing or motor noise, inspect the tabletop for rust or warping, and verify that the fence locks parallel to the blade. A saw that trips a breaker, has a frayed cord, or cannot be demonstrated should not be valued like a working example. Missing safety components or a fence that will not hold alignment can erase the savings of a low listing price.
Three realistic Porter-Cable saw buying scenarios
These examples illustrate how condition and included equipment affect a quote. They are comparison points rather than fixed national prices.
- Bare saw at $175: Tested 10-inch unit, worn blade, no stand. Add $35-$60 for a suitable blade and allow for transport.
- Complete setup at $325: Working saw, folding stand, fence, guard, and miter gauge. This is reasonable if the blade raises smoothly and the fence locks securely.
- Needs repair at $100: Saw powers on but has a damaged switch or alignment issue. A shop diagnostic may cost $50-$100, with repairs potentially adding $75-$250.
The lowest initial price is not necessarily the lowest total cost once missing equipment, repair, and transportation are included.
When repair costs exceed a replacement saw
Basic maintenance can be economical: a new blade may cost $25-$90, while cleaning and alignment materials often add $10-$30. Professional diagnosis or repair commonly runs $75-$250 before uncommon parts. If a motor, arbor, switch, or fence assembly needs replacement, parts availability can be uncertain because these saws are discontinued.
Compare the complete repair estimate with the price of a tested used saw or a new entry-level 10-inch jobsite saw. A repair approaching $200-$300 may make little sense on a worn unit with additional missing parts. For an older saw, repair is most defensible when the fault is limited, the essential parts are intact, and the repair total stays well below a sound replacement.
How local supply shifts Porter-Cable prices
Used-tool pricing varies with competition and transport. In large metro areas with frequent listings, comparable saws may sell 10%-20% below prices in smaller markets where few are available. Rural buyers may face fewer choices and an added $25-$60 trip or delivery expense; coastal or high-cost cities can also show asking prices 10%-25% above a broad-market estimate.
Compare completed or recently removed listings when possible, not just ambitious asking prices. A seller asking $450 for a bare saw may be less competitive than a complete $325 setup nearby. Local availability can shift the deal by $30-$100, so compare equivalent models and included accessories.
Ways to keep a table saw purchase under budget
Set a ceiling based on the saw’s working condition, not the seller’s original retail price. Request a short demonstration, photograph of the model plate, and a list of included parts before traveling. If the fence, guard, or stand is missing, price those items before making an offer rather than assuming inexpensive replacements will be easy to find.
Pickup can avoid delivery fees, but bring help and a vehicle that can safely carry the saw. Ask whether the seller will include spare blades or compatible accessories; avoid paying extra for worn blades or add-ons that do not fit. A tested, complete saw at a fair local price is usually a better value than a cheaper unit with uncertain repairs.