Roller door prices typically range from $500 to $3,500 installed, depending on opening size, steel thickness, insulation, and labor. Standard single-car doors cost less than wide, insulated, or custom-fit models, while removal of an existing door can add to the quote.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Single 8-by-7-foot door | $500 | $1,200 | $2,200 | Installed, basic steel |
| Double 16-by-7-foot door | $900 | $1,900 | $3,500 | Installed, standard opening |
| Door only | $350 | $900 | $2,200 | Excludes installation |
| Installation labor | $250 | $550 | $1,000 | More for difficult access |
What standard 8-by-7 and 16-by-7 doors cost
A basic, non-insulated steel roller door for a standard 8-by-7-foot opening generally costs $350-$1,200 for the door, or about $500-$2,200 installed. A standard 16-by-7-foot double door commonly runs $650-$2,200 for the unit and $900-$3,500 installed. Midrange installed prices are about $1,200 for a single door and $1,900 for a double door.
Those estimates assume a residential opening, ordinary access, and no major framing changes. Insulated or heavier-gauge models can push a single-door project above $2,500 and a double-door project past $4,000. Assumptions: U.S. residential pricing, standard steel, typical access, and no structural repair. For a basic installed door, budget roughly $60-$160 per sq ft of opening, including labor and hardware.
How steel, labor, and hardware appear on quotes
Quotes may combine components into one installed price, so buyers should ask what the contractor includes. A low door-only price is not comparable to an installed quote that covers tracks, springs, removal, and haul-away.
| Quote component | Typical range | What changes the price |
|---|---|---|
| Steel door and curtain | $350-$2,200 | Size, gauge, finish, insulation |
| Tracks, brackets, and hardware | $100-$450 | Door weight and system design |
| Installation labor | $250-$1,000 | Opening condition and access |
| Motor or opener | $250-$700 | Drive type and controls |
| Removal and disposal | $75-$300 | Old door weight and local fees |
Labor pricing can also be estimated as 4-8 hours for a straightforward installation at $75-$125 per hour, though contractors often quote a fixed job rate. Confirm whether the total includes tax, delivery, disposal, and opener setup before comparing bids.
Opening width, height, and insulation shift the price
Common residential sizes include 8-by-7 feet for a single garage, 9-by-7 feet for a wider single opening, and 16-by-7 feet for a double garage. A 16-by-8-foot door has more curtain material and may need heavier supports than a 16-by-7-foot model, often adding $150-$500, depending on construction.
Nonstandard openings, such as widths above 18 feet or heights above 8 feet, may require custom sizing and reinforced hardware. Expect custom fabrication to add roughly 15%-40% over a comparable standard unit. Insulation can add $200-$700 per door; thicker insulation and higher thermal ratings cost more. Measure the finished opening in several places, because even a 1-2-inch mismatch can trigger custom work.
Installation time and site access affect labor charges
A two-person crew commonly takes 3-6 hours to replace a standard door when the opening is sound. A new installation, a heavy insulated door, or a high ceiling can take 6-10 hours. Labor increases when installers must adjust framing, move stored items, work around tight side clearance, or install a new electrical outlet for an opener.
Framing repair may add $200-$1,000 or more, depending on rot, water damage, and the amount of lumber or trim needed. An electrical circuit or outlet can add $150-$500 if required. Ask the estimator to separate door installation from framing and electrical work so unexpected charges are visible.
Regional labor rates create different installed totals
Installed prices in lower-cost rural and Midwestern markets may be 5%-15% below the national middle range. Major metros and high-cost coastal areas often run 10%-25% higher because of labor rates, travel, and disposal fees. These differences apply to comparable doors and scopes; a local quote can still vary substantially with access and contractor availability.
For example, a standard single door with a typical $1,200 installed midpoint might land around $1,020-$1,140 in a lower-cost market, versus $1,320-$1,500 in a higher-cost metro. Compare at least three local quotes using the same size, insulation, opener, and removal requirements.
Insulated steel versus basic steel roller doors
Basic single-skin steel is usually the least expensive choice and suits detached garages where temperature control is not a priority. Insulated steel can reduce heat transfer and door noise, but costs more and may add weight, requiring compatible springs and hardware. Aluminum models may resist rust but can cost more than basic steel and may dent more easily.
For a standard single opening, basic steel installed commonly totals $500-$2,200, while insulated steel often runs $900-$2,800. Premium finishes, heavier gauge steel, or custom colors can add $150-$600. Choose insulation based on garage use and climate rather than paying for a rating that will not affect the space.
Removal, opener, and custom color add-ons
Removing and disposing of an old door typically adds $75-$300, with heavier or damaged doors costing more to handle. A new automatic opener generally adds $250-$700 installed; keypad controls, battery backup, or smart features can raise the equipment price. Custom colors and upgraded finishes often add $100-$500, while windows may add about $100-$400 depending on layout and glass.
Permit requirements vary by city and by whether the project changes the opening or structure. If a permit is needed, allow roughly $50-$300, plus any inspection or code-upgrade expense. Request written confirmation of permit responsibility and all add-ons before signing.
Keep roller door costs down with a matched scope
Keeping the existing opening and tracks only when they are compatible can avoid unnecessary framing work, but old tracks should not be reused unless the installer confirms they match the new door. A repair may be less expensive than replacement when the curtain is intact: spring or lock repairs often run $100-$350, while a damaged curtain or badly bent tracks may make replacement more practical.
Choose a standard size and finish, compare equivalent steel and insulation specifications, and schedule nonurgent work when contractors are less busy. Clear the garage and access path before installation to reduce delays. Do not compare a door-only price with an installed quote; align equipment, labor, disposal, and warranty coverage first.