A Stihl MS 360 Pro typically costs about $350-$750 used in the U.S., with clean, serviced saws often listed near $550. Price depends most on mechanical condition, included bar and chain, and whether the saw is an original Pro model, a rebuilt unit, or old stock.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Used saw, running | $250 | $550 | $900 | Condition, service history, and local demand affect asking price |
| Rebuilt or serviced saw | $500 | $750 | $1,000 | Verify what was replaced and whether work is documented |
| Old stock or exceptionally clean example | $700 | $950 | $1,300+ | Availability is limited; high asking prices do not guarantee value |
| Common replacement bar | $45 | $75 | $125 | Length, mount, and brand change the price |
Used Stihl MS 360 Pro prices by condition
The MS 360 is a discontinued professional 60 cc-class saw, so most buyers are comparing used equipment rather than current retail inventory. A saw that starts, idles, oils the chain, and cuts reliably commonly falls around $400-$700; a rough project saw may cost less but can need substantial parts and labor.
A fair working-saw budget is roughly $500-$650 before any immediate repairs. A higher price may make sense for documented engine work, excellent compression, a usable bar and chain, and a trustworthy seller. Assumptions: U.S. private-party prices, standard configuration, ordinary wear, and no shipping or sales tax.
What the bar, engine work, and labor add
Purchase price is only part of the expense. A worn chain, damaged sprocket, fuel-system trouble, or scored cylinder can quickly change the total. The table below gives typical independent-shop or parts-counter ranges; dealer availability for an older model varies.
| Cost item | Typical range | What changes the bill | Pricing basis |
|---|---|---|---|
| Bar and chain | $65-$160 | Bar length, pitch, gauge, and brand | Per set |
| Carburetor service or replacement | $40-$220 | Cleaning versus replacement and diagnosis | Parts and labor |
| Clutch, sprocket, or chain brake repair | $90-$280 | Which components are worn or damaged | Installed |
| Top-end engine repair | $250-$600 | Cylinder condition, parts availability, and shop rate | Installed |
| Inspection and tune-up | $50-$130 | Compression test, cleaning, and adjustment scope | Per visit |
Shop labor often runs about $75-$125 per hour, and a repair estimate can include a diagnostic charge. Ask whether the inspection fee is credited toward approved repairs.
How bar length and engine condition shift the quote
Many MS 360 setups use bars around 16-25 inches. A longer bar or additional bar-and-chain set can add $50-$150 or more, but a long bar does not automatically make a worn saw more valuable. Match the setup to the intended cutting work and confirm the bar mount, chain pitch, and gauge.
Engine condition matters more than cosmetic wear. A cold-start demonstration, steady idle, responsive throttle, functioning chain brake, and oil delivery are useful checks. Compression readings should be interpreted with a mechanic’s judgment rather than treated as a single pass/fail number; poor compression, deep cylinder scoring, or hard starting can mean several hundred dollars in repairs.
For a saw with uncertain history, reserve $150-$300 for inspection and common repairs before agreeing to a premium price. A missing bar, damaged starter, or faulty oiler also reduces the value, even if the engine runs.
Repair charges that can turn a bargain into a project
Small fixes may be economical, but a full engine rebuild can push the total near or above the cost of a better-maintained example. A $300 saw plus $400 in top-end work and $100 for a bar set reaches $800 before tax or transport. Obtain a written estimate that separates parts, labor, and diagnostic fees.
Check the serial number and model identification, and ask which parts are original or aftermarket. For a rebuilt unit, request the repair date, parts list, and any shop warranty terms in writing. Private sellers may offer no warranty, while a dealer or repair shop may provide limited coverage with exclusions.
Three MS 360 Pro buying scenarios with totals
| Scenario | Price calculation | Estimated total |
|---|---|---|
| Basic runner, 20-inch bar, minor tune-up | $400 saw + $90 service + $80 chain set | $570-$650 |
| Clean saw, 25-inch setup, documented maintenance | $650 saw + $120 bar and chain | $770-$850 |
| Low-priced project with engine repair | $275 saw + $350-$600 repair + $80 bar set | $705-$1,000 |
These are planning examples, not fixed quotes. Tax, shipping, parts compatibility, and a shop’s minimum charge can change the out-the-door price. Ask the seller to demonstrate the saw cutting safely rather than relying only on a brief idle test.
Regional used-saw prices from rural to city markets
Prices can vary with local logging, firewood, and tree-service demand. In rural areas with plentiful used equipment, comparable working saws may list about 5%-15% below a major metro market. In areas with fewer sellers or strong professional demand, asking prices can run 10%-20% higher; these are broad comparison ranges, not guaranteed regional rules.
Shipping can erase a lower online price. A $450 listing may add $40-$100 for shipping and packing, plus possible tax and the risk of buying without a hands-on inspection. Local pickup offers a chance to check cold starting, leaks, chain brake operation, and included accessories.
Ways to lower the MS 360 Pro purchase price
Compare several listings with the same bar length and similar condition, then value the saw and accessories separately. Request a cold start and ask about fuel mix, storage, recent repairs, and reason for sale. A seller who cannot demonstrate basic operation should not receive the same price as a documented, ready-to-work saw.
Set a repair reserve before negotiating and avoid paying extra for accessories that are worn or unnecessary. A sound saw with a shorter bar may be a better buy than a cheaper unit needing engine work. If the estimate approaches $800-$1,000, compare it with newer professional saws that have available parts and clearer warranty support.
Use the total ready-to-cut cost—not the listing price—to compare MS 360 Pro deals. Include repairs, bar and chain, transport, and applicable tax, and walk away if the seller’s claims cannot be checked.