A used Stihl TS 400 concrete saw typically costs about $300-$900, with many working examples priced near $550. Price depends on starting and cutting condition, included blade, maintenance history, and local availability; the model is discontinued, so buyers should compare used prices with newer saws and repair costs.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Used TS 400 saw | $300 | $550 | $900 | Working condition; price varies by wear and seller |
| Inspected or refurbished saw | $600 | $850 | $1,200 | May include service, warranty, or accessories |
| Compatible cut-off wheel | $40 | $90 | $180 | Price depends on diameter and blade type |
| Initial service allowance | $75 | $200 | $450 | Typical shop work; major engine repair can cost more |
Assumptions: U.S. private-party and equipment-dealer listings, standard used wear, and prices before sales tax or shipping.
What a used Stihl TS 400 usually costs
Private sellers commonly ask $300-$700 for a TS 400 that starts and runs but shows ordinary job-site wear. A clean, tested saw with a good starter, working water feed, and usable blade may reach $700-$900. Dealer-serviced units can cost more when they include a limited warranty or documented repairs.
A realistic budget for a ready-to-work used saw is about $650-$1,000 after a blade check and basic service. This assumes a sound engine, standard 14-inch cutting setup, and no significant damage. A saw that does not start, has low compression, or needs hard-to-find parts should be priced as a repair project, not as a working machine.
Where the TS 400 purchase price goes
A seller’s asking price is only part of the outlay. A worn blade, clogged air filter, damaged starter, or neglected fuel system can quickly turn a low-priced saw into an expensive purchase. Ask whether the machine has been run recently and whether the seller will demonstrate a cold start.
| Quote item | Low | Average | High | What it covers |
|---|---|---|---|---|
| Used saw | $300 | $550 | $900 | Machine only, depending on condition |
| Cut-off wheel | $40 | $90 | $180 | General-purpose or specialty 14-inch blade |
| Shop inspection | $50 | $100 | $175 | Starting, compression, and basic safety checks |
| Common repairs | $75 | $200 | $450 | Filters, ignition parts, carburetor work, or starter parts |
| Shipping or local delivery | $0 | $50 | $150 | Pickup is usually the least expensive option |
Budget for the saw, blade, and inspection separately instead of treating the asking price as the complete cost. A shop may charge a diagnostic fee that is applied to repair work; confirm that policy before authorizing service.
How engine condition and blade size shift the quote
Starting condition is one of the biggest price signals. A TS 400 that starts cold, idles steadily, and accelerates cleanly is worth more than one that only runs after warming up. Smoke, fuel leaks, inconsistent power, or a weak starter can indicate maintenance needs or more serious engine trouble.
Check that the saw is set up for the intended wheel diameter and that the guard, spindle, and water connections are intact. A 14-inch wheel is a common configuration, but fit and condition should be verified on the individual saw. Missing guards or damaged mounting parts can add expense and may make the saw unsuitable for work.
Condition can move a used-saw price by several hundred dollars, while a damaged engine can outweigh any discount. Ask about compression testing and recent service records rather than relying only on a seller’s description.
How much TS 400 labor and repair work adds
Small-engine shops commonly charge about $75-$125 per hour, with a diagnostic or minimum service fee often around $50-$125. Basic carburetor cleaning, filter replacement, or starter work may take one to three labor hours, depending on access and parts availability. An engine rebuild or extensive fuel-system repair can exceed $400 in labor and parts.
Set aside $150-$350 for ordinary catch-up service on a running saw, but get a written estimate before approving engine work. Because the TS 400 is an older model, ask the shop to confirm that the needed part can still be sourced and whether an available replacement is compatible.
Three TS 400 purchase examples with total budgets
A lower-cost purchase might be a private-party saw listed at $350, with a $60 blade and $100 inspection. The approximate total is $510 before tax, assuming the inspection finds no repair needs.
A typical work-ready example could cost $550, plus a $90 wheel and $200 in service. That puts the initial budget near $840, excluding delivery and tax. A dealer-serviced saw at $850 with a $100 blade and no immediate repair gives an estimated $950 total.
These examples show why a $300 listing is not automatically cheaper than a tested saw priced at $700. Compare complete ready-to-cut costs, and include any known repairs in the offer.
How regional supply changes used saw prices
In areas with active construction, concrete cutting, and equipment dealers, more listings can give buyers room to compare condition and negotiate. Remote or rural buyers may face fewer local options and $50-$150 in delivery or travel costs. Local asking prices can differ by roughly 10%-20% from a broad-market estimate, but condition and seller type usually matter more than state lines.
Check nearby listings and the cost of pickup before treating an online asking price as the local market rate. Shipping a used power tool can also involve carrier restrictions, packing charges, or delays, so confirm the total delivered price before paying.
When a newer cut-off saw is the better comparison
The TS 400 is discontinued, so buyers should compare its purchase-plus-repair budget with current or newer used cut-off saws. A newer used machine may cost $700-$1,500 or more depending on brand, size, age, and condition, while a new professional saw can be several thousand dollars. Exact alternatives vary, so compare the required blade diameter, power, weight, and service support.
If a TS 400 needs more than $400-$500 in repairs, price a replacement before committing to the work. Parts availability, warranty coverage, and downtime can make the lower purchase price less economical for frequent cutting.
Ways to lower the TS 400 cost without buying trouble
Ask the seller to start the saw from cold, demonstrate throttle response, and show the blade guard and water feed. Bring someone familiar with small engines or pay for a pre-purchase inspection when the machine will be used regularly. Price the needed blade and service before negotiating, and avoid paying extra for accessories that are worn or incompatible.
The safest savings usually come from verifying condition and controlling repair exposure, not choosing the lowest listing. For occasional use, renting a cut-off saw may be less expensive than buying a machine that needs immediate parts or ongoing service.