A Stihl TS 760 price is usually about $300-$900 for a used saw, with clean, tested examples sometimes listed near $1,200. The model is discontinued, so condition, included cutting equipment, parts availability, and local demand matter more than a current new-retail price.
Most buyers should budget about $600-$700 for a working saw, then allow extra for a blade, inspection, or repairs.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Used TS 760 saw | $300 | $650 | $1,200 | Condition and operation determine value |
| Replacement abrasive blade | $25 | $45 | $80 | Blade diameter and material rating vary |
| Inspection or basic service | $75 | $150 | $300 | More if the saw needs parts or repair |
| Ready-to-use budget | $400 | $800 | $1,500 | Includes a modest allowance for setup |
What a used Stihl TS 760 usually sells for
The TS 760 is an older, discontinued gas-powered cut-off saw, so pricing is based on private sales, used-equipment dealers, and the machine’s condition rather than a current manufacturer list price. A non-running or incomplete saw may fall near $200-$400; a working example with ordinary wear commonly lands around $500-$800. A clean saw with a tested engine and useful accessories can reach $900-$1,200.
These are practical used-market estimates, not a guaranteed national price or dealer quote. Ask whether the engine starts cold, idles, accelerates, and cuts under load. Cosmetic condition alone does not establish mechanical value. Assumptions: standard used condition, no major engine damage, and a complete saw with normal access to parts.
How engine, labor, and blade costs shape the quote
A seller’s asking price can exclude service, missing cutting gear, and transport. If a shop checks the saw before purchase, ask what the inspection covers and whether the fee applies toward repairs. Labor is commonly billed by the hour, while parts and consumables are separate.
| Quote item | Typical price | What it covers | Cost note |
|---|---|---|---|
| Used saw | $300-$1,200 | Powerhead and standard components | Running condition is the main distinction |
| Shop labor | $75-$125 per hour | Diagnosis, tuning, or repair | One to three hours can add $75-$375 |
| Abrasive blade | $25-$80 each | General cutting consumable | Check size and intended material |
| Diamond blade | $100-$350 each | Longer-life blade for suitable work | Price varies with diameter and grade |
| Pickup or delivery | $0-$150 | Local transport | Distance and seller policy determine charge |
For example, two hours of shop work at $95 per hour adds $190 before parts. A seller who has already serviced the saw may charge more upfront but provide a clearer account of its operation.
Which TS 760 condition details move the price most?
Engine health creates the widest price gap. Hard starting, low compression, fuel leaks, or inconsistent power can turn a $600 purchase into a repair project. A repair estimate above $300 may make a low-priced saw less attractive, especially when the needed components are difficult to source.
Check whether the blade guard, starter, handles, and water-feed connections are present and functional. Missing components can require separate purchases, and a worn clutch or damaged starter adds labor. Also confirm the blade diameter and guard configuration rather than assuming every included wheel fits the saw.
For a used machine, demonstrated cutting performance and a repairable parts list matter more than a seller’s claim that it “ran recently.” Request a cold start and a brief test cut where safe and practical. Inspection threshold: treat a saw needing multiple repairs or more than $300 in immediate work as a different price category.
How repair costs compare with buying another cut-off saw
Repair can make sense when the TS 760 has a sound engine and needs routine service or one limited repair. A carburetor adjustment or basic tune-up may cost roughly $75-$200; more involved fuel-system, starter, or clutch work can run $150-$400 or more, depending on parts and labor. Major engine work may exceed the value of an ordinary used example.
Compare the repair total with another used saw and with a newer model of similar capacity. New professional cut-off saws commonly cost roughly $1,200-$2,000, depending on model and dealer pricing, before accessories. That higher purchase price buys a newer machine and generally simpler warranty support, but it does not guarantee the best value for occasional use.
Set a repair ceiling before authorizing work, and compare the complete repaired cost with a tested replacement. Warranty coverage on an older used TS 760 is often limited or absent, so get any dealer promise in writing.
Regional availability changes used TS 760 asking prices
Prices can run about 10%-20% higher in construction-heavy metro areas where contractors and rental businesses create demand. In rural areas, listings may be cheaper, but transport and limited repair access can offset the savings. These are market tendencies, not fixed regional price rules; the number of working examples nearby has a large effect.
Shipping a heavy saw may add $50-$150 or more, and carrier restrictions or packaging requirements can complicate delivery. A local pickup lets the buyer inspect the saw and test its controls before paying. Compare several nearby listings and include transport in the total rather than comparing asking prices alone.
A $500 local saw can cost less overall than a $425 listing that requires shipping and immediate service.
What to inspect before paying for a discontinued saw
Ask for the model identification, maintenance history, and details of any engine or carburetor work. Check the starter action, throttle response, fuel lines, guard, and visible cracks or repairs. Confirm whether the price includes a usable blade, tools, or other accessories, and clarify whether the saw can be returned if it fails a promised test.
Parts availability can vary by component and location. Before buying a non-running unit, call a local small-engine shop with the exact model and fault description. Ask whether it will service the TS 760 and whether parts can be obtained; a low purchase price has little value if the shop cannot complete the repair.
Pay more only when the seller can show evidence of operation, service, or included value. Avoid relying solely on a video of the saw starting briefly, since that does not prove it cuts correctly or remains reliable when warm.
How to keep a TS 760 purchase within budget
Compare the same condition and included equipment, not just the advertised price. Request an itemized total for the saw, blade, service, and delivery. If a listing is incomplete, price the missing parts before negotiating. A seller may accept less for a saw with a worn blade, but a discount is useful only if the replacement cost is known.
Choose a blade suited to the material and expected workload rather than paying for premium equipment that will rarely be used. For occasional cutting, a properly inspected used saw may be economical; for frequent professional work, downtime and parts delays can outweigh the lower purchase price. Bundle pickup with an inspection when possible, but do not skip the test to save a small fee.
Keep a $150-$300 reserve for initial maintenance and consumables unless the seller documents recent service. That reserve helps distinguish an affordable purchase from a machine that only appears inexpensive at first.