Swing out garage doors typically cost $3,000-$9,000 installed for a standard two-car opening, with custom hardwood or large doors reaching $12,000 or more. The swing-out garage doors price depends on door material, opening width, hinges and hardware, structural changes, and local labor rates.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Two-car door pair, installed | $3,000 | $6,000 | $12,000+ | Standard opening; custom wood costs more |
| Single-car door, installed | $1,800 | $3,500 | $7,000 | Price varies by material and design |
| Door materials, per sq ft | $15 | $35 | $75+ | Basic steel or composite through custom wood |
| Installation labor | $600 | $1,400 | $3,000 | Higher for framing or alignment work |
What a two-car swing-out door costs installed
A typical pair for a 16-by-7-foot opening costs about $3,000-$9,000 installed. A common midrange project using insulated steel, fiberglass, or engineered wood runs around $4,500-$6,500. Custom cedar, heavy hardwood, decorative windows, or a nonstandard opening can push the total to $9,000-$15,000.
These doors open outward on side hinges rather than lifting overhead. The estimate assumes a sound, square opening, standard hardware, and no major framing changes. Assumptions: U.S. midrange labor rates, ordinary site access, and standard colors. For a standard two-car opening, $6,000 is a reasonable planning figure before custom upgrades.
Regional labor rates shift the installed quote
Labor and delivery can change the final price even when the door specification is identical. Quotes in high-cost metro areas and coastal markets may be 15%-30% above a typical national estimate. Smaller cities and rural areas may come in 5%-15% below it, although limited installer availability can erase the difference.
Remote delivery, difficult parking, or a long carry to the garage can add $150-$600. Local contractor minimums also matter: a single-car installation may have a higher per-door rate than one door in a larger project. Compare written quotes from installers who regularly fit side-hinged doors, not only overhead models.
Hinges, framing, and door panels behind the quote
The price is not just the door panels. Heavy swing-out leaves need sturdy hinges, secure jambs, and a level opening so the doors close evenly and resist wind. The table shows common budget shares for a standard two-car job; upgrades and repairs can change each line.
| Quote item | Typical range | How it affects price | Unit or scope | Notes |
|---|---|---|---|---|
| Door panels | $1,500-$5,500 | Largest material expense | $15-$75+ per sq ft | Material, insulation, and finish |
| Hinges and latch hardware | $250-$900 | Heavy-duty sets cost more | $125-$450 per leaf | May include hold-open hardware |
| Installation labor | $600-$2,000 | More time for heavy or custom leaves | $75-$125 per hour | Often one or two installers |
| Framing and trim | $300-$1,800 | Repairs or reinforcement add cost | Per opening | May be needed for weak jambs |
| Removal and disposal | $150-$500 | Depends on old door and haul distance | Per project | Ask whether the quote includes disposal |
Confirm whether the quote includes hardware, weatherstripping, removal, and any jamb reinforcement.
Door width, weight, and opening condition change the price
Opening size is a major cost driver. A single 8-by-7-foot opening typically needs less material and lighter hardware than a 16-by-7-foot pair; widths above 18 feet or doors taller than 8 feet often require custom construction and stronger hinges. Expect larger custom configurations to add roughly 20%-50% over a standard-size estimate.
Material weight and exposure also matter. Solid hardwood doors are heavier than many steel or composite models and may require reinforced jambs. Wind-exposed locations, uneven concrete, rotted framing, or an opening out of square by more than about 1/2 inch can require extra adjustment or carpentry, adding $300-$2,000. Ask the installer to measure the opening and inspect the hinge-side framing before final pricing.
Installation time and crew size for hinged leaves
A straightforward pair generally takes a two-person crew about 6-10 hours, including removal of an existing door and fitting the hinges, latch, and weather seal. Custom or oversized doors may take 1-2 days, especially if carpentry or finish work is included. Labor often totals $600-$2,000, with complex work reaching $3,000.
Because the doors swing outward, the installer also needs room to position and adjust each leaf. A blocked driveway, uneven apron, or limited access can slow the job. Request a separate labor allowance for framing, painting, or electrical work rather than assuming it is part of the door installation.
Control material and framing choices to lower the price
Standard dimensions and stock finishes usually cost less than custom sizes, specialty colors, and decorative glass. Steel or quality composite can provide a carriage-house appearance at a lower price than solid hardwood. Before replacing sound framing, ask whether targeted jamb reinforcement will safely support the hinges.
Get at least three itemized estimates that specify door material, insulation, hardware grade, disposal, finish work, and warranty. Avoid paying for unnecessary decorative options, but do not substitute light-duty hinges for hardware suited to the door’s weight. The best savings come from simplifying the design while keeping the hinge and frame system properly rated.
Three sample quotes for common swing-out door projects
A basic single-car replacement with a 9-by-7-foot insulated steel door may total $2,700-$4,000: roughly $1,600-$2,300 for the door, $700-$1,100 for 7-9 labor hours, and $200-$600 for removal and trim. The lower end assumes an undamaged opening and standard hardware.
A standard 16-by-7-foot pair in composite or engineered wood may run $4,800-$7,200. A sample breakdown is $2,800-$4,200 for panels, $1,000-$1,700 for labor over 10-14 hours, and $500-$1,300 for hardware and finishing. A custom cedar pair with windows and reinforced jambs may cost $8,500-$13,500, including $5,000-$8,500 for the doors and additional carpentry.
These examples illustrate quote differences, not fixed national prices. Compare the same opening size, material grade, hardware, and included work when evaluating totals.