Cambria Torquay quartz countertops typically cost about $110-$165 per square foot installed, with many standard kitchens landing between $4,000 and $7,000. The final price depends on countertop area, slab use, edge profile, cutouts, removal, and local fabrication and installation rates.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Installed countertop | $110 per sq ft | $135 per sq ft | $165 per sq ft | Material, fabrication, and standard installation |
| 30-sq-ft kitchen | $3,300 | $4,050 | $4,950 | Simple layout, standard edge |
| 40-sq-ft kitchen | $4,400 | $5,400 | $6,600 | Before optional removal or upgrades |
| Material allowance | $70 per sq ft | $90 per sq ft | $115 per sq ft | Dealer and slab pricing vary |
Assumptions: U.S. pricing for a standard residential project, ordinary access, and professional fabrication and installation.
What a Cambria Torquay Countertop Usually Costs
For a typical project, installed Torquay pricing often falls around $110-$165 per square foot. That estimate generally combines the quartz, measuring, fabrication, delivery, and installation. Higher local labor rates, complex seams, large cutouts, or an upgraded edge can push a quote above that range.
A small vanity or kitchenette with 10-15 square feet may cost roughly $1,300-$2,600, though minimum fabrication and travel charges can make a small job expensive per square foot. A 30-square-foot kitchen is commonly $3,300-$4,950, while 40 square feet is about $4,400-$6,600 before separate demolition or plumbing work.
For a straightforward 35-square-foot kitchen, a useful planning budget is approximately $3,850-$5,775 installed. This assumes standard countertop depth, a simple layout, one sink cutout, and no major changes to cabinets or plumbing. Ask whether the quote prices the material by installed square foot or by slab, since the methods can produce different totals when remnants or slab yield are involved.
Torquay is a Cambria design rather than a separate grade of generic quartz. Dealer availability, current slab pricing, and the fabricator’s purchasing arrangement can affect the material allowance. A written estimate should identify the design, slab or lot selection, included fabrication, and any charges not covered by the per-square-foot rate.
How Slabs, Fabrication, and Installation Shape the Quote
Installed pricing is a bundle of material and trade work, but estimates do not all include the same items. The following ranges show common components for a standard kitchen; they are not meant to be added mechanically because a contractor may combine them in a single installed rate.
| Quote component | Typical range | How it is priced | What changes the charge |
|---|---|---|---|
| Cambria Torquay material | $70-$115 per sq ft | Slab allocation or area | Dealer price, slab yield, remnant availability |
| Template and fabrication | $20-$40 per sq ft | Shop work and cutouts | Seams, sink type, edge, cooktop opening |
| Installation labor | $10-$25 per sq ft | Often bundled with fabrication | Stairs, access, number of pieces, setting needs |
| Delivery and handling | $150-$500 per project | Trip or delivery fee | Distance, slab handling, site access |
| Old counter removal | $5-$15 per sq ft | Removal and disposal | Material weight, backsplash, disposal rules |
| Sink or cooktop cutout | $150-$400 each | Per opening | Opening dimensions and finishing detail |
Labor may be estimated as a bundled project rate or calculated from shop and installation hours. A planning calculation for separate labor is For instance, 12-18 combined shop and site hours at $60-$100 per hour represents $720-$1,800 in labor, though many fabricators include this work in the installed square-foot price.
Confirm whether measurement, sink cutout, delivery, and installation are included before comparing bids. A low material rate can still produce a higher final bill if fabrication, removal, or delivery appears as a separate line item.
Why Slab Yield, Edge Profile, and Cutouts Change the Price
The most important Torquay-specific pricing issue is slab yield. Countertops are cut from full slabs, and the pattern direction, layout, and required seam placement determine how much material can be used. A 30-square-foot layout does not necessarily require only 30 square feet of purchased slab; unusual dimensions or a large island may require another slab or leave costly unused material.
Layout size matters in practical thresholds. A kitchen under about 25 square feet may fit a smaller or remnant-based order if the pieces align with available stock. Projects above roughly 45-50 square feet, or those with a long island, may need more than one slab depending on slab dimensions and cut plan. Request a drawing that shows seams and slab allocation.
Edge selection can also shift the quote. A standard eased edge is often included, while a decorative or laminated edge may add about $10-$30 per linear foot. A countertop with 40 linear feet of exposed edge could therefore add $400-$1,200 if the chosen profile is priced separately. The exact increase depends on profile complexity and shop rates.
Cutouts and finish details contribute additional charges. A sink opening commonly costs $150-$400, and a cooktop opening may be similar or higher when it requires extra finishing. A full-height quartz backsplash can add approximately $40-$90 per square foot installed, depending on thickness, wall preparation, and the number of outlets or inside corners.
Ask the fabricator to price the actual measured layout, not just the room’s approximate square footage. A drawing helps reveal whether the quote assumes one or multiple slabs, where seams will fall, and which edges receive a finished profile.
Which Torquay Design Choices Can Keep the Project in Budget
The largest controllable savings usually come from reducing waste and limiting custom work, rather than choosing a cheaper countertop appearance after the design is set. Keep runs close to standard depths where possible, avoid unnecessary short returns, and compare the cost of a large island with a simpler layout. Cabinet changes made for the countertop can add substantially more than the stone itself.
Choose an included standard edge if its appearance suits the project. A decorative profile around an island can add hundreds of dollars, particularly when several exposed sides are involved. Similarly, a short quartz backsplash may be less expensive than taking the material up the entire wall, though tile or another finish should be compared as a separate installed cost.
Request pricing for the same Torquay slab selection and scope from at least two fabricators. Compare the total and line items, not only the advertised square-foot rate. Check whether each quote includes templating, installation, delivery, sink cutout, faucet holes, removal, disposal, and tax. A quote that excludes one of these can appear lower by several hundred dollars.
Keeping the layout, edge, and cutout list consistent makes bids easier to compare and reduces surprise charges. If a usable remnant is available for a small vanity or secondary surface, ask whether it matches the main project’s design and whether the savings exceed the shop’s minimum charge.
How Installed Torquay Prices Compare Across U.S. Markets
Local labor, delivery distance, and fabricator competition can move the total even when the slab is identical. As a broad planning comparison, metropolitan markets with high labor and operating costs may run 10%-25% above a national midrange estimate. Smaller cities and rural areas may come in 5%-15% below it, but limited fabricator availability or a long delivery route can erase that difference.
For a 35-square-foot kitchen budgeted at $135 per square foot, the midpoint is $4,725. A market running 15% higher could put the comparable scope near $5,434, while one 10% lower could be around $4,253. These percentages are useful for initial planning, not a substitute for a local written quote.
Transport can be a distinct issue outside major service areas. A fabricator may charge roughly $150-$500 for delivery and handling, with a higher fee for a long route, difficult access, or specialized slab equipment. Confirm whether the delivery charge is included in the installed rate and whether a site visit is necessary before the final estimate.
Use local quotes for the final budget because labor and logistics vary more than a national average suggests. Compare bids that specify the same slab design, measured area, edge, cutouts, and removal scope.
How Long Templating and Installation Take
After cabinets are ready, a fabricator typically needs a site visit to template the countertop. Installation often follows several business days to a few weeks later, depending on slab availability, shop workload, and scheduling. The on-site installation for a standard kitchen may take about 4-8 hours; complex layouts, multiple seams, or difficult access can extend the visit.
Shop work includes cutting and finishing the measured pieces, while the crew handles placement, seam work, and final adjustments. Homeowners generally need to have cabinets secured and level before templating. If cabinets or walls change after measurement, the fabricator may need to ret template or recut pieces, potentially adding fees and delaying the job.
Some contractors charge a separate template or trip fee, commonly around $150-$350, which may be credited toward the completed order. Ask whether the quote includes a second visit, what happens if the site is not ready, and who disconnects and reconnects the sink and cooktop. Plumbing work is often excluded from countertop installation.
Having cabinets and appliances in their final positions before templating helps avoid rework charges. Clarify the expected schedule and whether the kitchen will be unavailable during removal, installation, and plumbing reconnection.
Three Kitchen Layouts Show the Likely Total
The examples below use approximate installed rates and show how scope influences the budget. Actual totals depend on local pricing, slab layout, and the fabricator’s inclusions.
| Project scenario | Area and scope | Example pricing | Estimated total |
|---|---|---|---|
| Small galley | 25 sq ft, standard edge, one sink cutout | 25 × $125, plus $250 removal | $3,375 |
| Typical family kitchen | 35 sq ft, eased edge, sink and cooktop openings | 35 × $140, plus $350 cutout allowance | $5,250 |
| Kitchen with island | 50 sq ft, upgraded edge, complex seam layout | 50 × $155, plus $800 upgrades | $8,550 |
The small galley example assumes no extra slab charge or major access difficulty. A modest square-footage job can still have a higher effective rate because minimum charges are spread across fewer feet. The family kitchen example represents a straightforward midrange project with two functional openings and basic removal.
The island project reflects higher area and additional detailing, not a universal surcharge for every island. A large slab, waterfall panel, or seam-matching requirement can raise the material and shop allowance. A waterfall side alone may add about $800-$2,000 per side, depending on dimensions, material use, and fabrication complexity.
Use the examples as scope comparisons, then replace their area and allowances with the fabricator’s measured quote. The most useful estimate identifies whether premium island details require extra slab material.
Removal, Plumbing, and Backsplash Charges to Check
Old countertop removal and disposal are frequently excluded from an advertised installed price. Removal may cost $5-$15 per square foot, with heavier stone, a bonded backsplash, or difficult access raising the charge. Disconnecting and reconnecting a sink or cooktop may require a plumber or appliance professional, often adding $150-$500 or more depending on the work and local service rates.
Wall preparation is another potential extra. If the old counter has a short backsplash that damages drywall during removal, patching and paint can add about $150-$600 for a modest kitchen. A full-height Torquay backsplash costs more because it uses additional quartz and requires precise wall measurements, outlet cutouts, and careful handling.
Permit needs are uncommon for a countertop-only replacement, but associated plumbing, electrical, or cabinet alterations may trigger local requirements. Any code-related work should be priced separately from the stone installation. Sales tax treatment also varies by state and by how materials and labor are billed, so ask whether tax is included in the written total.
Request a written list of exclusions, especially demolition, plumbing, wall repair, and tax. Those items can add several hundred dollars even when the countertop itself matches the original estimate.