Fascia replacement typically costs $7-$22 per linear foot installed, with many U.S. homeowners paying about $1,200-$2,800 for a typical house. The final price depends on total roofline length, board material, labor rates, access, and whether gutters or damaged roof edges must be removed or repaired.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Installed fascia | $7 per linear ft | $14 per linear ft | $22 per linear ft | Removal and installation; standard access |
| Typical house project | $600 | $1,800 | $4,000 | About 80-180 linear ft |
| Fascia board material | $1 per linear ft | $4 per linear ft | $10 per linear ft | Pine, primed wood, or PVC/composite |
| Painting or sealing | $2 per linear ft | $4 per linear ft | $7 per linear ft | May be included with wood installation |
Fascia replacement prices by roofline length
Contractors commonly price fascia by the linear foot, including removal of the old board and installation of a replacement. A 100-linear-foot job may run $700-$2,200, while replacing 200 linear feet can cost $1,400-$4,400. Small jobs may have a minimum charge, so a short repair does not always cost proportionally less.
For a straightforward 150-linear-foot replacement, a practical budget is about $1,050-$3,300. That estimate assumes sound rafter ends, ordinary one- or two-story access, and no extensive gutter, soffit, or roof-edge work. Assumptions: Typical U.S. labor rates, standard access, and basic wood or PVC fascia.
What removal, boards, and labor add to the quote
The quote usually combines materials, crew time, and removal. Painted wood can require more finishing than prefinished metal, while gutter detachment and disposal add time. The ranges below are typical planning figures and may overlap when a contractor gives a bundled installed rate.
| Quote item | Low | Average | High | Pricing basis |
|---|---|---|---|---|
| Fascia board | $1 | $4 | $10 | Per linear ft, material only |
| Installation labor | $4 | $8 | $14 | Per linear ft |
| Removal and disposal | $1 | $3 | $6 | Per linear ft |
| Gutter removal and reset | $3 | $7 | $12 | Per linear ft, when needed |
| Painting or sealing | $2 | $4 | $7 | Per linear ft |
Charges differ by contractor: some include disposal and basic finishing in the installed rate, while others list them separately. Ask whether the written estimate includes old-board removal, gutter handling, finishing, and cleanup.
How board material and rot change the final price
Material choice affects both the purchase price and future upkeep. Primed pine is often a lower-cost option, but it needs paint and protection from moisture. PVC or composite boards usually cost more upfront and resist rot; aluminum fascia is also available, often as a cover over an existing board rather than a structural replacement.
Damage behind the fascia can raise the bill. Replacing short sections of rafter tail, repairing roof sheathing, or correcting water entry may add $150-$1,000 or more, depending on how much framing is affected. A job above 200 linear feet, a roof pitch over 8:12, or a two-story eave can require added crew time or lift equipment. Get hidden wood damage priced separately from the fascia-board allowance.
How long fascia work takes and what labor costs
A crew of two may replace 80-150 linear feet in one workday when access is clear and the roof edge is sound. Larger homes, detailed corners, high eaves, or extensive gutter work can extend the job to two or three days. Labor rates often fall around $50-$100 per worker-hour, but many contractors quote a project total rather than billing hourly.
Scaffolding, a lift, or steep-roof safety measures can add roughly $150-$600 per day, particularly when the fascia sits above a second story. Ask the contractor to identify any access-equipment charge and expected workdays before approving the estimate.
Why fascia rates differ by region and access
Urban markets with higher wages and overhead may price fascia installation 10%-25% above the national midpoint. Rural areas can be 5%-15% lower when travel is limited, though a long drive or a small isolated repair may trigger a service minimum. Coastal locations may also favor rot-resistant materials or extra weatherproofing, increasing the material budget.
These percentages are broad comparisons, not fixed regional tariffs. Local contractor availability, roof height, and the season can matter as much as the state. Compare estimates for the same linear footage, material, removal scope, and finish rather than comparing totals alone.
When a fascia patch costs less than replacement
For a small area of isolated damage, a contractor may charge $150-$500 to replace a short section, depending on access and whether painting is needed. Replacing a full run is often more economical when rot appears in several places, boards are peeling throughout, or the fascia no longer holds gutters securely. A patch over soft wood can hide the cause without fixing it.
Ask whether the contractor will inspect the roof edge and explain the source of moisture. If only the fascia is damaged, a full soffit or gutter replacement may be unnecessary. Choose repair when the surrounding boards and rafter ends are solid; replace longer runs when damage is widespread.
Ways to lower a fascia quote without cutting corners
Measure the roofline with the contractor and confirm the linear footage by elevation. Bundling fascia work with planned gutter or exterior painting can reduce repeat setup charges, but the quote should still show each task separately. If gutters are reusable, ask whether they can be detached and reset rather than replaced.
Compare at least three written bids with matching board material, thickness, finish, disposal, and repair allowances. Primed wood may reduce upfront cost where regular repainting is acceptable; PVC can make sense where moisture exposure is persistent. Avoid paying for a premium material upgrade unless the site conditions justify it. Clear scope and comparable line items are the most reliable ways to find a lower price.
Extra charges for gutters, permits, and finish work
Many fascia-only replacements do not need a building permit, but local rules vary, especially if structural framing or roof-edge construction changes. Permit and inspection costs, when required, may add $50-$300. Painting, color matching, gutter screens, and replacement fasteners can also appear as separate line items.
Contractors may charge $75-$200 for a small-job minimum or diagnostic visit, sometimes credited toward approved work. Water damage discovered after removal should be documented with photos and a change-order price before repairs proceed. Confirm permit responsibility, finish expectations, and the process for hidden damage in the contract.