A Thelin Gnome pellet stove may cost about $3,000-$5,000 for the appliance when available, with a typical installed total of $4,500-$7,500. Final pricing depends on whether the stove is new or used, local availability, venting work, hearth requirements, and labor; older or scarce inventory can push the asking price beyond these ranges.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Stove only | $3,000 | $4,000 | $5,000 | New or dealer-held inventory; price depends on availability and included parts |
| Installed project | $4,500 | $6,000 | $7,500 | Typical replacement or straightforward installation |
| Used stove | $800 | $1,800 | $3,500 | Condition, age, service records, and included vent parts matter |
| Pellet fuel | $5 | $7 | $10 | Approximate price per 40-pound bag, varying by region and season |
What a Thelin Gnome pellet stove typically costs
Budget roughly $3,000-$5,000 for a new or dealer-stock Gnome before installation, but confirm that the quote covers the exact model and components. The Gnome is a compact pellet stove, and its price is not as consistently published or widely stocked as that of mass-market models. Dealer inventory, discontinued or older stock, and regional supply can make advertised prices hard to compare. A quote should identify the model, condition, included controls, trim, and warranty.
For a straightforward installation, a practical total budget is about $4,500-$7,500. That assumes a typical U.S. home, standard wall or roof venting, accessible installation area, basic hearth protection, and no major electrical or structural work. A complex chimney route, removal of an existing appliance, or code upgrades can add several hundred to several thousand dollars.
Used listings can be much cheaper, commonly $800-$3,500 for the stove itself, but the lowest asking price is not necessarily the lowest project cost. A unit without a working control board, exhaust blower, or available replacement parts may require repairs before it can be safely operated. Assumptions: U.S. pricing ranges, standard residential access, and no major chimney reconstruction.
Where the purchase price goes in a Gnome installation
The appliance is only one part of the quote; vent materials, installer labor, and code-compliant floor protection can materially change the total. The table gives planning ranges for a typical project. Actual charges vary with the vent route, local labor rates, and whether the work is a replacement or a new installation.
| Quote item | Typical price | Unit or scope | What changes the charge |
|---|---|---|---|
| Gnome stove | $3,000-$5,000 | Per stove | Condition, stock, finish, controls, warranty |
| Pellet vent and fittings | $400-$1,200 | Per installation | Pipe length, elbows, wall thimble, termination |
| Installer labor | $600-$1,500 | Per job | Access, vent path, testing, local hourly rate |
| Hearth pad or floor protection | $150-$700 | Per installation | Required dimensions and material choice |
| Permit and inspection | $50-$400 | Per jurisdiction | Local permit rules and inspection fees |
| Removal and disposal | $150-$600 | Per old appliance | Weight, disconnection, hauling distance |
A vent kit may be priced separately even when the stove listing appears complete. Buyers should ask whether the quote includes a fresh-air intake, termination cap, wall or ceiling pass-through, sealants, and any needed electrical outlet. Some components from an old stove may not be compatible or suitable for reuse.
Installer labor is often estimated as a project charge, but the underlying time can help compare bids. A basic replacement may take 4-8 hours, while a new route through a wall or roof can require 8-14 hours. At roughly $75-$150 per hour, 6-10 labor hours imply $450-$1,500 before travel, testing, or minimum service charges.
Which Gnome size, vent route, and finish change the quote
Room size and vent layout matter more than a small trim upgrade because they determine whether the stove suits the space and how much installation work is needed. The Gnome is intended for smaller spaces than many full-size pellet stoves. Before comparing prices, verify the exact model’s rated heat output and the manufacturer’s sizing guidance against the home’s insulation, ceiling height, climate, and open floor plan.
Heating a well-insulated 500-800-square-foot area is a different assignment from trying to heat 1,000-1,200 square feet in a cold or poorly insulated home. If the stove is undersized, it may run continuously and still fail to maintain comfortable temperatures. If it is oversized for a small room, frequent cycling and heat management can be troublesome. Ask the dealer to explain the sizing basis rather than relying only on a broad square-foot claim.
Vent distance also affects the bill. A short, direct wall exit may use about 3-6 feet of vent pipe, while a longer route with multiple elbows or a roof termination may need 10-20 feet or more. Each bend, pass-through, and difficult access point can increase material and labor charges. A different finish or included accessory can add hundreds of dollars, but confirm which options are actually available for the specific Gnome being quoted.
Electrical needs should be checked before installation. Pellet stoves use electricity for their feed and blower systems, so the installer may need to add an outlet or address an unsuitable circuit. A nearby compliant outlet may add little cost; new wiring or panel work can add roughly $150-$800 or more depending on distance and site conditions.
How much does Gnome installation add?
Expect labor and standard setup to add about $1,000-$2,500 to a stove purchase when venting and floor protection are included. Straightforward replacements generally fall near the lower end, especially if the existing location is appropriate and the vent system is in good condition. A new installation often costs more because it requires a new vent path, floor protection, electrical checks, and commissioning.
Installers may charge a flat rate, hourly labor, or a minimum visit fee. Typical rates can range from $75-$150 per hour, while some markets charge more for certified technicians or travel to remote locations. Ask whether the estimate includes startup, draft or exhaust checks, owner instruction, and a return visit if the stove needs adjustment.
Work duration is not the same as elapsed scheduling time. A crew may finish a simple job in one day, but an inspection appointment or special-order vent component can delay completion. Confirm who is responsible for permits and inspection coordination. If a quote is substantially lower than other bids, check that it includes safe vent termination and required clearances rather than just setting the appliance in place.
Why Gnome prices vary by U.S. region
Local installer availability and product scarcity can produce wider price differences than a modest change in trim or accessories. In major metropolitan areas, labor and permit fees may run about 10%-25% above a national planning estimate. Rural locations can have lower hourly rates but higher travel charges, fewer technicians, and longer waits for parts. These are useful comparison allowances, not fixed regional tariffs.
Cold-weather markets often have more demand for pellet-stove service during autumn and early winter. A scheduled installation in spring or summer may be easier to arrange, while emergency work during a cold snap can carry a rush charge of about $100-$400 or require a wait. Fuel prices also differ: a 40-pound pellet bag may cost about $5-$10, with delivery or premium fuel adding to the household budget.
Scarcity is especially relevant for the Gnome. If a dealer has a model in stock, the price may be tied to its age, condition, and remaining warranty rather than a current standard retail list. Compare the same configuration across quotes and ask for the serial number, manufacturing or purchase history, and written warranty terms. A higher price may be reasonable if it includes verified condition, local service, and a clear parts-support plan.
What removal, venting, and hearth work add
Old-appliance removal and vent changes are common reasons an installation exceeds the initial stove-only estimate. Removing an existing pellet stove typically costs $150-$600 when it can be disconnected and carried out without major dismantling. Masonry or heavy wood stoves, difficult stairs, or disposal restrictions can raise the fee. Ask whether the contractor will remove only the appliance or also haul away the old pipe and hearth materials.
Reusing a vent system can save money only when it is compatible, correctly sized, in sound condition, and accepted by the installer and local code. A replacement vent system may cost $400-$1,200 for ordinary parts and installation conditions, while a long or complicated route can exceed that range. Do not assume that a vent used by another stove meets the Gnome’s installation requirements.
Floor protection is another variable. A basic pad may cost $150-$300, while a larger or decorative hearth can cost $400-$700 or more. If the floor needs reinforcement, the stove location requires a new opening, or a wall must be repaired after removal, those are separate work items. Request line-item pricing for each so optional finish work is not confused with required safety work.
Is a used Gnome cheaper than a new pellet stove?
A used Gnome can lower the appliance purchase price, but condition and parts availability determine whether it saves money overall. A working used unit listed for $800-$2,000 may be economical if it includes service records and can be inspected before purchase. A tested, clean example with accessories may be advertised for $2,000-$3,500. Private sales often provide no warranty, and moving or reinstalling the stove is usually the buyer’s responsibility.
Before paying, inspect the burn pot, door gasket, firebox, exhaust path, wiring, auger, fans, and controls. Ask the seller to demonstrate a cold start and normal operating cycle, and have a qualified technician evaluate questionable equipment. A repair allowance of $200-$800 may cover a limited service visit or common component replacement, but a major control, motor, or vent problem can cost more.
A new alternative from another manufacturer may cost about $2,000-$4,500 for the appliance, with installation bringing many projects to roughly $3,500-$6,500. That comparison is useful if a Gnome is priced unusually high or hard to service. Compare rated output, physical dimensions, vent requirements, warranty coverage, local technician support, and parts supply—not purchase price alone.
Ways to trim a Gnome stove budget without cutting safety
The safest savings usually come from avoiding unnecessary scope, not reducing vent quality or skipping inspection. Get at least two itemized quotes that specify appliance condition, vent materials, labor, floor protection, permits, removal, and startup. Comparing matching scopes exposes whether a low bid omits work or a high bid includes optional upgrades.
If the current vent route is serviceable and approved for the model, ask whether any components can be retained after inspection. Do not reuse pipe just to cut the price if its condition, diameter, clearances, or compatibility is uncertain. Similarly, choose a standard hearth pad that meets installation requirements instead of paying for decorative masonry that does not improve safety or function.
Schedule nonurgent work outside the busiest heating season when installer calendars are more flexible. Buying pellets before winter demand rises may also help control fuel expense, provided they are stored dry. Ask for the total delivered price, not just the bag price, and compare the cost per ton where bulk delivery is available.
For a used stove, make the inspection part of the purchase decision. A technician’s assessment may cost roughly $100-$250, but it can reveal missing parts or damage before the buyer commits. If a repair is minor and parts are available, repair may be less expensive than replacement; if the stove has extensive wear or uncertain support, a low purchase price can become a costly project.