Whirlpool control board replacement typically costs $250-$700 total, with an average near $450; refrigerator and range boards can push a repair above $800. The appliance model, board availability, diagnostic fee, labor time, and whether wiring or sensors also need repair drive the estimate.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Washer or dryer | $200 | $400 | $650 | Part and standard service labor |
| Refrigerator | $300 | $550 | $900 | Depends on board location and model |
| Range or oven | $250 | $500 | $850 | Higher for premium or discontinued models |
| Control board part only | $100 | $275 | $600 | OEM and specialty boards may cost more |
Assumptions: U.S. standard service call, compatible replacement board, normal access, and no additional failed parts.
Whirlpool control board prices by appliance type
Most standard Whirlpool board replacements land between $250 and $700 including parts and labor. A washer or dryer repair often totals $200-$650, while a refrigerator or cooking appliance can cost $300-$900 because its board may be more expensive or harder to reach. Compact appliances and older models may have lower-cost parts, but discontinued boards can cost more when sourced through specialty suppliers.
These estimates generally assume one board, one technician, and a routine repair. The average of roughly $450 is a planning figure, not a guaranteed quote. A technician should verify the appliance’s model number and test related components before ordering a board.
What board, labor, and service fees add to the quote
The replacement board is often the largest single charge, but diagnosis and labor can add $100-$250. Prices below are typical U.S. ranges; individual shops may combine fees or apply the diagnostic charge toward the repair.
| Quote item | Low | Average | High | Common basis |
|---|---|---|---|---|
| Control board | $100 | $275 | $600 | Part only, depending on appliance |
| Diagnostic or trip fee | $75 | $110 | $150 | One service visit |
| Installation labor | $90 | $160 | $300 | About 1-2.5 hours |
| Shipping or disposal | $0 | $20 | $60 | Expedited delivery or old-part handling |
Appliance technicians commonly charge $75-$150 per hour, with a minimum service charge in some markets. A straightforward board swap may take 45-90 minutes; access panels, built-in installation, or troubleshooting can extend the visit.
Model number, board type, and symptoms change the estimate
A matching part number can make a larger difference than the appliance’s age alone. Basic washer control boards may cost $100-$250, while refrigerator main boards or range electronic controls commonly run $200-$500. Premium models, combination appliances, and models with multiple control modules can exceed those ranges.
Board prices can also rise when a model has been discontinued or requires an OEM part rather than a compatible replacement. A control panel and a main electronic board are not always the same component. If a quote names a “control board,” ask for the part number and which board is being replaced.
Symptoms such as a blank display, failure to start, or incorrect temperature do not prove the board is faulty. A failed fuse, door latch, sensor, power supply, or damaged wiring can produce similar symptoms. Testing first helps avoid paying for a board that will not solve the problem.
How long a Whirlpool board repair takes
Most routine replacements take about 1-2.5 hours on site, excluding parts-order delays. A top-load washer board may be accessible in under an hour, while a refrigerator board behind an interior panel or a range board behind a control console can take longer. Built-in appliances and cramped laundry closets can add labor.
If the technician must order a board, the repair may be delayed several days or longer, particularly for older models. Rush shipping can add $20-$60 or more. Confirm whether the estimate includes a return trip if the part is not available during the diagnostic visit.
When wiring faults or a second failed part raise the bill
Related electrical damage can turn a single-part repair into a broader service job. Burned connectors, damaged harnesses, or a failed sensor may add $30-$200 in parts and labor, depending on access and the component. A technician should identify the cause of board failure, since installing a new board without correcting a short or power problem may lead to another failure.
Ask whether the estimate includes diagnosis, the replacement board, labor, and any return visit. A written quote should state the warranty period for both parts and labor. Manufacturer parts may carry a separate warranty, while independent repair companies set their own coverage terms.
Repairing the board compared with replacing the appliance
Board replacement is often reasonable when the appliance is under 8-10 years old and the repair is well below half the cost of a comparable new unit. Board-level electronic repair, when available, may cost $150-$350, but it can take longer and may not include the same warranty as a complete board replacement.
For an older appliance with multiple failures, compare the full repair quote with replacement, including delivery, installation, and removal. A $700 repair on a basic washer near the end of its service life deserves closer comparison than a $400 repair on a newer refrigerator. There is no universal cutoff; condition, repair history, and replacement prices matter.
Three Whirlpool repair quotes with different scopes
These examples show how appliance type and labor time can shift a realistic invoice. Actual prices vary by region, model, part source, and service-company fee structure.
| Example | Parts | Labor and fees | Estimated total |
|---|---|---|---|
| Top-load washer, standard board | $180-$250 | 1 hour plus $90-$125 diagnostic | $370-$525 |
| French-door refrigerator, main board | $300-$450 | 1.5 hours plus $100-$150 diagnostic | $510-$825 |
| Electric range, control board and harness | $250-$400 | 2 hours plus $90-$140 diagnostic | $490-$840 |
Assumptions: Standard access and no premium weekend or emergency surcharge.
Ways to lower a Whirlpool board replacement bill
Confirm the diagnosis and total installed price before approving a part order. Provide the technician with the full model number, serial number, and a clear description of the symptoms; this can help identify the correct board and reduce repeat visits. Compare two or three written quotes, checking that each includes the same part type, diagnostic fee, labor, and warranty.
Ask whether the diagnostic fee is credited toward the repair and whether a compatible board is available with a clear warranty. Avoid replacing a board based only on an error code or online symptom match. If the appliance has more than one suspected fault, request separate prices for each repair so the necessary work can be weighed against replacement.