A 4 burner cooktop typically costs $300-$2,500 for the appliance, with installation bringing a straightforward replacement to about $500-$3,400. The final 4 burner cooktop price depends most on fuel type, surface material, electrical or gas work, countertop fit, and local labor rates.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Cooktop only | $300 | $1,100 | $2,500 | Four-burner gas, electric, or induction models |
| Basic replacement installation | $200 | $450 | $900 | Uses existing compatible hookups and countertop opening |
| Installed project total | $500 | $1,550 | $3,400 | Standard unit and routine replacement work |
| New circuit or gas-line work | $250 | $700 | $1,800 | Additional work can exceed these amounts in complex homes |
What a four-burner cooktop costs by fuel type
Most buyers spend $500-$3,400 for a cooktop and basic installation. A 30-inch, four-burner gas or radiant-electric unit with a standard finish often lands near $500-$1,500 installed. Midrange induction and premium glass or stainless models commonly total $1,200-$2,700. High-end brands, specialty finishes, and extensive hookup changes can push a project above $3,400.
Appliance-only prices vary widely. Entry-level coil electric cooktops can start around $250-$500; radiant glass models often run $400-$1,200; gas models commonly cost $350-$1,500; and four-zone induction units are often $700-$2,500. These are broad retail ranges, not guaranteed sale prices. Bundled promotions, delivery, and included accessories can change the checkout total.
A standard replacement in the same fuel type and opening is usually the least expensive scenario. The estimate assumes a typical 30-inch unit, ordinary access, no countertop alteration, and existing electrical or gas service in usable condition.
Assumptions: U.S. midrange pricing, standard 30-inch opening, ordinary access, and no major code or utility upgrades.
How appliance, hookup, and labor charges build the quote
A written estimate should separate the cooktop from removal, fitting, connection, and any modifications. Basic installation labor is often a few hours, but a fuel conversion or cutout change can require additional trades and appointments. The component ranges below describe common costs; they are not all added to every job.
| Cost component | Typical range | Pricing basis | What it covers | When it rises |
|---|---|---|---|---|
| Cooktop | $250-$2,500 | Per unit | Four-burner appliance and standard controls | Induction, premium brand, specialty finish |
| Labor | $150-$500 | $75-$150 per hour | Disconnect, set, connect, and test | Hard access or multiple trades |
| Equipment and supplies | $25-$150 | Per job | Fittings, sealant, connectors, minor parts | Nonstandard connection or replacement parts |
| Delivery and disposal | $50-$200 | Per order or unit | Appliance delivery and old-unit haul-away | Stairs, restricted delivery, remote location |
| Permits or inspection | $0-$250 | Per jurisdiction | Required permit and inspection charges | New circuit, gas line, or local requirement |
Some installers charge a minimum service fee of $100-$200 even when the work takes less than an hour. A retailer’s installation package may bundle labor and haul-away, but it may exclude new wiring, countertop work, or plumbing and gas modifications. Ask whether the quoted price includes testing, materials, tax, and a return visit if the unit cannot be connected on the first appointment.
Labor is only comparable when the quote defines the same tasks.
How cutout size, power, and fuel change the estimate
Cooktop dimensions and home infrastructure can matter as much as the appliance’s sticker price. A replacement that fits the existing opening may need only a small adjustment to brackets or trim. A unit with different dimensions can require countertop work, while switching between gas, electric, and induction can trigger electrical or gas-system upgrades.
Countertop cutting or enlargement often adds $150-$600 for a straightforward adjustment, with stone, quartz, or fragile surfaces potentially costing more or requiring a countertop specialist. If the cutout is too large, a compatible model or trim kit may be less expensive than rebuilding the surface. Confirm the manufacturer’s cutout dimensions and required clearances before ordering.
Electrical requirements are another major variable. Many electric cooktops require a dedicated 240-volt circuit; induction models may need a circuit sized for their specific amperage. If an appropriate circuit is already present and accessible, connection work may be modest. Installing a new circuit can add roughly $300-$1,200, and a distant panel, finished walls, or panel-capacity issue can raise the price further.
Gas cooktops need a suitable gas connection, shutoff, and compatible pressure and fittings. Extending a line may cost $250-$900 for an accessible, short run; longer routes, concealed piping, or a new shutoff can increase the charge. A change from gas to electric or electric to gas is more involved than replacing a like-for-like unit and may require both a licensed trade and local inspection.
Two thresholds deserve special attention: a cutout change of even a few inches can require countertop labor, and a new 240-volt circuit can add hundreds of dollars. Exact electrical capacity and opening size should be checked against the appliance installation specifications, not assumed from the old cooktop.
Installation time and trade rates for a cooktop swap
A straightforward replacement typically takes 1-3 hours on site when the new unit fits the opening and uses existing service. A licensed appliance installer or electrician may charge about $75-$150 per hour, often with a minimum visit fee. A separate gas fitter may have a similar service minimum, depending on market and job complexity.
Work can stretch across half a day or more if crews need to cut a countertop, pull a new circuit, extend a gas line, or coordinate an inspection. Some installations require separate visits for measurement, modification, and final connection. Scheduling a countertop contractor before ordering helps avoid a cooktop delivery sitting unused while the opening is corrected.
Labor rates are generally higher in major metropolitan areas and places with higher living costs. Rural areas may have lower hourly rates but higher travel charges or fewer available specialists. A quote that looks cheaper may not include a second trade, disposal, or the required electrical and gas testing.
Ask for labor hours and the hourly or flat rate, then confirm the list of included tasks. That makes a $250 installation quote easier to compare with a $500 quote that includes removal, haul-away, connection materials, and testing.
Three realistic installed price examples
Project examples show how the appliance and site work combine. Actual local quotes may fall outside these illustrations, especially where a permit, premium surface, or difficult access is involved.
| Scenario | Appliance | Labor and extras | Estimated total |
|---|---|---|---|
| Same-size radiant electric replacement | $450-$800 | $200-$350 for removal, fit, and connection | $650-$1,150 |
| Induction replacement with circuit already installed | $900-$1,800 | $250-$500 for connection, supplies, and haul-away | $1,150-$2,300 |
| Gas cooktop with a short new line | $500-$1,200 | $450-$1,000 for labor, line work, and inspection where required | $950-$2,200 |
For a second comparison, a 30-inch basic gas cooktop installed into a compatible opening could total roughly $600-$1,400. A premium four-zone induction model with a new 240-volt circuit and modest countertop adjustment could reach $2,000-$3,800. These examples assume no major electrical panel replacement or extensive stone repair.
The most useful quote compares the same appliance class and the same scope of work. A low appliance price can still produce a high project total if the opening, circuit, or gas connection needs alteration.
Regional labor and delivery differences across the U.S.
National averages are only a starting point. Cooktop prices may be similar across online retailers, but local installation, delivery, and trade availability vary. In higher-cost metro areas, labor and service charges can run about 15%-35% above a typical national estimate. Smaller cities and suburban markets often sit closer to baseline, while rural projects may add a travel or minimum-service fee.
Regional differences also reflect housing stock. Older homes may have undersized electrical panels, outdated wiring, or gas connections that do not match current installation requirements. Dense urban buildings can mean elevator reservations, restricted delivery windows, and additional handling. A remote home may have fewer installers able to serve the area, which can increase scheduling delays or the cost of a second trip.
Delivery fees commonly range from $50-$150, while installation of an appliance delivered by a retailer may be priced separately. Haul-away can add $25-$100 if it is not included. Confirm whether the delivery crew will bring the unit into the kitchen or only to the home entrance, and whether the old cooktop must already be disconnected.
Request a local, itemized quote rather than applying a national labor average directly. Regional percentages are planning estimates; the actual difference depends on contractor availability, site access, and the work required.
When induction or repair beats a low-cost replacement
A basic radiant or coil electric cooktop is usually the least expensive purchase, while induction costs more upfront but can offer precise temperature control and quick response. A four-burner induction model commonly costs $700-$2,500 before installation. It needs compatible magnetic cookware and an appropriately rated electrical connection, so buyers should include those requirements in the comparison.
Repair may cost less than replacement when the fault is limited to a switch, igniter, control, or a single heating element. Common diagnostic and repair visits can total $150-$500, depending on the part and local labor. A failed control board or cracked glass surface can cost $300-$900 or more to repair, making replacement more attractive on an older entry-level unit.
Before replacing a gas unit, check whether the issue is a worn igniter, clogged burner, or damaged control rather than a failed cooktop. A service call and simple repair may cost $150-$350. A damaged glass top, multiple failed components, or a model with unavailable parts can shift the economics toward a new appliance. Repair estimates should include both diagnosis and the part warranty.
Compare repair cost with the full installed replacement total, not just the new cooktop’s shelf price. A $400 repair can be reasonable on a relatively new premium model but less appealing when the appliance is old and additional failures are likely.
Ways to trim the four-burner cooktop bill
Keep the same fuel type, width, and cutout dimensions when a suitable replacement exists. Reusing a working dedicated circuit or accessible gas connection avoids major trade work. Measure the opening and verify the required clearances before purchase; choosing a unit by outside width alone can lead to costly rework or a return fee.
Compare at least three written quotes with matching appliance specifications and job scope. Ask each installer to list removal, connection materials, testing, delivery, disposal, permits, and any countertop work separately. Check whether an appliance retailer’s package includes the necessary connection labor or only a basic set-in. Clarifying exclusions can prevent a low initial estimate from growing after delivery.
Choose features based on actual use. A standard finish and conventional controls may cost less than premium glass, smart connectivity, or specialty trim. Avoid paying for an unnecessary fuel conversion or a higher-output model that requires an electrical upgrade. If the old cooktop still works, scheduling a planned replacement rather than an emergency service can give more time to compare appliance sales and installer availability.
Some preparation is safe for homeowners, such as clearing cabinets and the work area, but gas disconnection, electrical wiring, and countertop cutting should be handled by qualified professionals. Doing hazardous work without proper credentials can create safety risks, damage, and insurance or code problems. Ask the installer what preparation is allowed and whether the home’s local rules require a permit or inspection.
The biggest savings usually come from avoiding an unnecessary circuit, gas-line extension, or countertop modification. Confirm compatibility before ordering, then compare complete installed prices rather than selecting solely by the lowest appliance tag.