Belgard Noon pavers typically cost about $6-$12 per square foot for materials, while a professionally installed patio often totals $18-$35 per square foot. The final price depends on the selected slab, project size, base preparation, access, delivery distance, and local labor rates.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Noon pavers only | $6/sq ft | $9/sq ft | $12/sq ft | Dealer pricing varies by color and availability |
| Installed patio | $18/sq ft | $26/sq ft | $35/sq ft | Includes typical base, setting, and labor |
| 300-sq-ft patio | $5,400 | $7,800 | $10,500 | Before unusual drainage or access work |
| Delivery | $150 | $350 | $700 | Depends on distance, load, and unloading needs |
Belgard Noon Pavers Price for a Typical Patio
For a standard ground-level patio with a compacted aggregate base, buyers commonly budget $18-$35 per square foot installed. A 300-square-foot project is roughly $5,400-$10,500, with about $7,800 representing a middle-range estimate. This assumes ordinary site access, a straightforward layout, standard edge restraint, and no major demolition or drainage correction.
Material-only pricing is usually around $6-$12 per square foot, but retailers may quote by pallet, piece, or coverage area. Confirm the exact Noon product, dimensions, thickness, finish, color, and coverage before comparing quotes. Assumptions: U.S. dealer pricing, standard ground installation, normal access, and no major excavation.
For early budgeting, allow about $26 per square foot installed, then adjust for site preparation and local labor. Premium layouts, extensive cuts, difficult delivery, or a more complex base can exceed the high range. Local estimates should also identify whether tax, disposal, and edge materials are included.
What Goes Into a Noon Porcelain Paver Quote
A complete quote separates the pavers from base construction and installation. Noon is a porcelain paving product, so the setting method matters: a ground-supported patio typically uses a prepared aggregate base, while some elevated or rooftop applications use pedestals and require different detailing. The contractor should specify the assembly rather than quote a generic paver installation rate.
| Quote component | Typical range | Pricing basis | What it covers |
|---|---|---|---|
| Noon pavers | $6-$12 | Per sq ft | Slabs, before waste |
| Base aggregate and bedding | $2-$5 | Per sq ft | Typical excavation fill and leveling materials |
| Installation labor | $7-$14 | Per sq ft | Layout, cutting, setting, and joint work |
| Edge restraint and joint supplies | $1-$3 | Per sq ft | Perimeter restraint and compatible joint materials |
| Equipment and delivery | $150-$700 | Per project | Transport, unloading, and small-equipment charges |
| Removal and disposal | $2-$6 | Per sq ft | Existing patio removal, when required |
These ranges are planning estimates, not a fixed Belgard retail schedule. The base and labor figures vary with excavation depth, soil conditions, crew size, and local rates. For example, 40-60 labor hours at $60-$100 per hour equals $2,400-$6,000 in labor before equipment or materials.
Ask for separate material, labor, base, delivery, and removal line items. A single installed-price figure can conceal differences in excavation, slab waste, joint treatment, or the paver setting system. Confirm whether the quote includes tax and whether the supplier charges a restocking fee for extra unopened product.
How Slab Size and Base Conditions Shift the Quote
Large-format porcelain slabs can require more careful handling and more precise support than small concrete pavers. A 24-by-24-inch layout, if that is the size quoted by the dealer, has different cut and handling needs from a smaller format. Verify the actual Noon dimensions on the current product specification, because available sizes and finishes can vary by market.
Plan to order about 5%-10% extra for a simple rectangular patio. A diagonal, curved, or heavily interrupted layout may require 10%-15% extra because of cuts and breakage. On a 300-square-foot patio, that means ordering approximately 315-345 square feet rather than buying exactly the measured area.
Base depth and drainage are major cost drivers. A stable, well-drained site may need limited excavation, while soft soil, standing water, or a patio adjoining a house can require deeper removal, added aggregate, or drainage work. If excavation expands from a typical 6-8 inches to 10-12 inches, hauling and aggregate quantities rise substantially.
Changing from a simple rectangle to a complex pattern can add $1-$4 per square foot. Extra cuts around steps, posts, drains, and curves take time and create more offcuts. A slope that directs water toward the home may also need correction rather than simply being covered with pavers.
Where Homeowners Can Trim the Installed Price
Keep the patio footprint and layout simple before asking for bids. Rectangular edges reduce cutting, waste, and labor, while a clearly marked scope makes estimates easier to compare. If a design includes several small landings or curved borders, compare its added price with a single larger, uncomplicated paved area.
Choose a color and finish that local dealers stock. Special orders can bring longer lead times, higher freight, or a larger minimum purchase. Ask whether multiple nearby projects can share a delivery, but confirm that the shipment can arrive when the site is ready and that unloading is included.
Existing concrete may sometimes serve as a suitable base for an overlay, depending on condition, drainage, height, and the installation method. Cracked or uneven concrete should not automatically be covered; movement can affect the new surface. Ask the installer to price both a repair or overlay option and full removal when technically appropriate.
Save by controlling scope, not by skipping base preparation or drainage. Request comparable bids using the same square footage, paver allowance, waste percentage, base depth, edge restraint, and disposal terms. Avoid paying for upgrades that do not solve a specific performance or design need.
How Long Noon Paver Installation Takes
A crew of two or three may complete a straightforward 300- to 500-square-foot patio in about 3-6 working days. That period can include excavation, base placement and compaction, layout, cuts, and final joint work. The schedule is not continuous in every method: some bedding or setting systems require particular weather or curing conditions.
Labor rates commonly fall around $60-$100 per worker-hour in many U.S. markets, though contractors often quote the full project rather than an hourly rate. A small job may have a minimum charge even when installation takes only a few days. Tight side-yard access, hand carrying, steps, and limited equipment access can add crew hours.
For a basic patio, installation labor often works out to about $7-$14 per square foot. Work requiring extensive cutting, stairs, a retaining edge, or an elevated pedestal system can cost more. Assumptions: Two- or three-person crew, normal weather, accessible site, and a ground-level patio.
Ask whether the stated duration counts only active work or includes delivery and site preparation. Supplier lead time is separate from installation time, and a special-order color may delay the start even when the crew has availability.
Three Patio Quotes for 300, 500, and 800 Square Feet
The examples below use a planning rate of $26 per square foot for a standard installation, including typical paver material, base, and labor. Delivery and removal are shown separately to make the total easier to compare. Actual bids depend on local conditions and the written product specification.
| Project | Pavers ordered | Base installation | Extra charges | Estimated total |
|---|---|---|---|---|
| 300 sq ft rectangle | 315 sq ft at $9/sq ft = $2,835 | Labor and base about $4,965 | $350 delivery | $8,150 |
| 500 sq ft patio with cuts | 550 sq ft at $9/sq ft = $4,950 | Labor and base about $8,050 | $500 delivery | $13,500 |
| 800 sq ft replacement | 840 sq ft at $9/sq ft = $7,560 | Labor and base about $13,240 | $1,600 removal and delivery | $22,400 |
In the 500-square-foot example, a 10% waste allowance suits a layout with some cuts; a very simple rectangle may need less. The 800-square-foot replacement includes a combined allowance for delivery and removal, but not major grading or drainage. At the same assumptions, the totals equal about $27, $27, and $28 per finished square foot.
Use the examples as quote checks, not guaranteed market prices. A lower number may omit disposal, base work, or enough pavers for cuts; a higher number may reflect difficult access or added site work. Ask contractors to explain any difference greater than about 15% between bids.
Noon Porcelain Compared With Concrete Pavers
Standard concrete pavers often cost about $3-$8 per square foot for materials and $12-$25 per square foot installed, depending on style and site work. Noon porcelain material can run higher, with installed pricing commonly around $18-$35 per square foot. The comparison should account for appearance, surface characteristics, product availability, and the installation assembly—not just the initial slab price.
Some porcelain installations need skilled cutting and careful handling, which can increase labor relative to basic concrete pavers. On the other hand, the best choice depends on the specific application and manufacturer instructions. Check the product specification for thickness, intended use, slip-related performance information, and installation requirements before treating two products as interchangeable.
Concrete pavers may be less expensive upfront, especially for a straightforward patio using widely stocked styles. Natural stone can range broadly, roughly $10-$30 per square foot for material and more installed, depending on stone type and fabrication. These alternatives can have different sealing, color variation, and maintenance needs.
Compare installed totals for the same area and base design. A lower material cost may be offset by installation demands, delivery, or additional preparation. Conversely, an expensive material may not justify its cost if the intended patio design does not need its particular look or specification.
Regional delivery and labor differences to budget for
Installed pricing can vary by roughly 10%-25% between lower-cost rural markets and high-cost metropolitan areas. Urban labor, parking limits, restricted delivery windows, and disposal fees can raise a quote; rural customers may face higher freight charges or fewer contractors familiar with porcelain paving. These differences are local, so a national average cannot predict a particular project precisely.
Freight can matter because pavers are heavy and are commonly moved as palletized loads. A local supplier may charge $150-$350 for a routine delivery, while a longer trip, special unloading, or separate small loads can bring the fee to $400-$700 or more. Confirm whether the truck can reach the unloading location and whether a forklift or other equipment is included.
Climate and site conditions also affect preparation. Freeze-thaw exposure, heavy rain, expansive soil, or a steep yard may require careful attention to drainage and base stability. These conditions do not automatically require a specific extra, but the contractor should explain how the proposed assembly suits the site.
Get at least two local installed quotes and verify the delivery address assumptions. Ask whether the price includes unloading at the curb or placement near the patio, and whether the contractor or buyer handles pallet disposal.
What to confirm before accepting a Noon paver estimate
Check that the estimate names Belgard Noon and identifies the selected color, size, finish, quantity, and waste allowance. Product lines and stock can vary among dealers, so a general description such as “porcelain pavers” is not enough to confirm that the quoted material matches the intended selection.
Review the base depth, excavation, compaction, drainage approach, edge restraint, and joint material. If the job is an overlay or uses pedestals, the proposal should state that clearly and explain the support system. Ask who is responsible for permits or inspections if local rules require them; requirements depend on the municipality and project conditions.
Clarify payment milestones, change-order rates, schedule, warranty coverage, and responsibility for damaged or short-shipped material. Keep a small amount of matching product for future repairs if the supplier permits an additional purchase, since a later replacement batch may not match perfectly.
A useful estimate states both the included work and the exclusions. Before signing, compare total price, per-square-foot price, material quantity, and preparation scope rather than relying on a single headline number.