The Bostitch SB-1664FN price typically ranges from about $70 to $160 for a used tool, while remaining new-old-stock units may list for $180 to $300 or more. The final price depends on condition, included accessories, seller, shipping, and whether the discontinued model is being compared with a current 16-gauge finish nailer.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Used SB-1664FN | $70 | $115 | $160 | Working condition, tool only or basic case |
| New-old-stock SB-1664FN | $180 | $240 | $300+ | Sealed or lightly handled stock; limited availability |
| Comparable new 16-gauge nailer | $120 | $190 | $300 | Current models, depending on features and kit contents |
| 16-gauge finish nails | $10 | $20 | $35 | Approximate box price; length and quantity affect cost |
What a Bostitch SB-1664FN Usually Costs
The SB-1664FN is a pneumatic straight 16-gauge finish nailer designed for finish carpentry and trim work. Since it is an older model and may not be stocked by regular retailers, prices are less consistent than those for current nailers. A realistic shopping budget is $70-$160 for a functioning used unit and $180-$300 for new-old-stock inventory.
For most buyers, a fair used-tool target is around $90-$130 when the nailer fires consistently and includes a usable case. Lower-priced listings may be tool-only, untested, or worn; higher asking prices often reflect clean condition, original packaging, or a seller charging a premium for scarce stock. Shipping and sales tax can add roughly $10-$35 to an online purchase.
The nailer accepts 16-gauge straight finish nails, generally in the 1-1/4-inch to 2-1/2-inch range. That capacity makes it suitable for many trim and molding tasks, but it is not a substitute for a framing nailer or a narrow-crown stapler. Buyers should verify the exact magazine specifications and operating condition before purchase, especially when a listing uses only a partial model number.
Assumptions: U.S. online and local resale listings, standard working condition, tool-only or basic accessories, before sales tax.
What the Nailer Quote Includes Beyond the Tool
A listing price may cover only the nailer, or it may include a case, fittings, manual, and sample nails. Those additions have practical value, but they do not automatically justify a large markup. A complete comparison should separate the tool price from shipping, consumables, and any repair allowance.
| Quote component | Low | Typical | High | What changes the amount |
|---|---|---|---|---|
| Used nailer | $70 | $115 | $160 | Wear, test status, seller warranty |
| Case and fittings | $0 | $10-$25 | $40 | Original case, air connector, manuals |
| Shipping | $0 | $10-$25 | $40 | Distance, carrier, seller packaging |
| Finish nails | $10 | $20 | $35 | Length, brand, box count |
| Repair allowance | $0 | $20-$50 | $100+ | Seals, driver, trigger, parts availability |
A low listing can become a poor deal if shipping, missing parts, or repairs push the total close to a new comparable tool. Air hoses and compressors are not usually included; a buyer who already owns compatible equipment does not need to add those costs to the purchase budget.
For a one-tool purchase, check whether the seller has tested the nailer under air pressure. A description such as “powers on” is not enough for a pneumatic tool: the buyer needs confidence that it cycles, feeds nails, and does not leak air continuously. If no test is offered, price the unit as an unknown-condition tool rather than as a ready-to-use nailer.
How Condition, Nail Length, and Model Scarcity Shift Price
Condition is the largest price variable. A tested unit with a clean magazine, working depth adjustment, and no major air leak can sit near the middle or upper end of the used range. A tool with an intermittent trigger or an unknown firing history should cost substantially less because diagnosis and parts can erase the apparent savings.
Ask for a function test using nails near both ends of the tool’s stated range, rather than relying on cosmetic appearance. Check that it feeds 1-1/4-inch and 2-1/2-inch nails reliably, if those lengths are listed for the specific model, and that the depth adjustment changes how far fasteners set into the workpiece.
Scarcity also matters. If the SB-1664FN is difficult to find locally, a seller may price it above a newer equivalent even when the newer tool has a better warranty. Compare the total cost against current 16-gauge models before paying a collector-like premium for an older production tool. The SB-1664FN is an everyday shop tool, so rarity alone does not establish a higher functional value.
Accessories can shift a sensible offer by about $10-$40, depending on whether the original case and useful fittings are present. A damaged case is not a major problem if the tool is protected for transport, while missing proprietary or difficult-to-source components deserve closer scrutiny. Confirm that the nose, magazine latch, and contact trip are intact before agreeing to a price.
Regional price differences are modest compared with condition and shipping. In large metro areas, a local used listing may run around 5%-15% higher than a rural listing because more buyers compete for tools. Rural sellers may ask less, but travel and limited opportunity to test the nailer can offset the difference.
When a Current 16-Gauge Nailer Is a Better Buy
Compare the SB-1664FN with current pneumatic 16-gauge finish nailers, not with cordless models or framing tools that do different work. A basic current pneumatic model commonly costs $120-$200, while feature-rich kits can reach $250-$300. The exact model, warranty, included case, and depth-control features determine whether the higher purchase price is justified.
| Choice | Typical price | Included value | Cost trade-off |
|---|---|---|---|
| Used SB-1664FN | $70-$160 | Established pneumatic design | May have wear and limited parts support |
| New basic pneumatic 16-gauge | $120-$200 | New seals, current warranty | Requires an air compressor and hose |
| Premium pneumatic kit | $200-$300 | Case and additional controls or fittings | Higher upfront cost for occasional users |
| Cordless 16-gauge nailer | $250-$450 | Battery-powered mobility | Battery platform raises initial cost |
Buying used makes the strongest cost case when the SB-1664FN is tested and costs at least $40-$60 less than a comparable new pneumatic tool. If the price gap is smaller, a new unit’s warranty and known condition may be worth the difference. A cordless model can reduce setup time at sites without an air compressor, but its battery and charger are part of the price comparison.
For occasional trim work, a basic pneumatic model can be a lower-cost alternative if the buyer already has a compressor. For frequent jobsite use, consider availability of replacement parts and the cost of downtime, not only the initial tool price. A newer model is not automatically better, but its service support may be easier to verify.
Three Purchase Scenarios From Tool-Only to Ready-to-Work
These examples show how the sticker price changes once common extras are included. They are planning estimates, not fixed market quotes, because individual sellers and shipping costs vary.
| Scenario | Tool and condition | Added costs | Estimated total |
|---|---|---|---|
| Local bargain | Used tested unit, $80 | $15 for a nail box | $95 |
| Typical online used buy | Clean used unit, $115 | $20 shipping and $20 nails | $155 before tax |
| New-old-stock purchase | Unopened unit, $240 | $25 shipping and $20 nails | $285 before tax |
The online used example costs about $155 before tax, so it should be compared with new tools near the $150-$200 range. A buyer who already has compatible 16-gauge nails can subtract the consumables line, while a local pickup may eliminate shipping and allow an in-person firing test.
For a repair-risk example, a $70 untested nailer plus $25 in shipping and a possible $50 service bill totals $145 before tax. That is not necessarily a bad purchase if the fault is simple and parts are available, but it is not a safe assumption. The buyer should treat the repair amount as a reserve, not as a guaranteed repair quote.
What Pneumatic Tool Repairs and Parts Can Add
Routine maintenance is inexpensive when the nailer is operating correctly. Depending on the tool’s instructions, a small amount of pneumatic tool oil may cost about $5-$12, while a compatible hose fitting commonly costs $5-$15. Avoid adding oil if the model’s instructions specify an oil-free operating procedure or otherwise limit lubrication.
A basic seal or o-ring repair may cost roughly $20-$60 in parts and supplies, while professional diagnosis and labor can bring a repair to $50-$125 or more. A damaged driver, trigger assembly, or hard-to-find component can make repair uneconomical, particularly if the final bill approaches the cost of a new basic pneumatic nailer.
Labor pricing depends on the repair shop and the fault. A shop may charge a minimum diagnostic fee of about $25-$50 even if the owner declines the work; more involved service can require 1-2 labor hours at roughly $75-$125 per hour.
Before purchasing a faulty unit, ask whether replacement parts are available for the exact model and whether the seller can identify the symptom. Air leaking from the exhaust, failure to feed, and a driver that sticks can point to different repair needs. A “needs a rebuild” description is too vague to support a confident repair estimate.
How Labor and Setup Affect the Cost of Using It
The nailer itself does not require paid installation, but using it efficiently depends on a compatible compressor, air hose, and fittings. A buyer who owns those items can keep the startup cost close to the tool and nail budget. A basic compressor can cost around $100-$250, and a hose and fittings may add $20-$60, although larger compressors and premium hoses cost more.
For someone starting without air equipment, the complete pneumatic setup may cost $190-$470 before tax, rather than the tool’s $70-$160 used price alone. This estimate combines a used nailer, basic compressor, hose and fittings, and one box of nails; it does not include other tools or a larger compressor intended for multiple air-demanding jobs.
Setup time is usually a smaller expense than equipment, but it matters on short jobs. Connecting the hose, setting pressure, loading the magazine, and testing depth can take about 10-20 minutes. On trim work, test a scrap piece before fastening finished material; correcting an overdriven or misplaced nail can cost more time than the initial setup.
If a contractor charges labor, the nailer’s purchase price is generally not a separate customer line item. Tool costs are commonly included in the overall labor rate or job estimate. A homeowner should therefore avoid treating a tool purchase as a per-room installation charge unless the contractor’s quote explicitly itemizes equipment rental or materials.
Ways to Lower the SB-1664FN Price Without Taking on Excess Risk
Set a maximum total before contacting sellers. For a used, tested tool-only unit, a practical ceiling is often $130-$150 before tax, unless the listing includes valuable accessories or unusually strong proof of condition. For new-old-stock, compare the full delivered price with current models instead of assuming discontinued means more valuable.
Prioritize a firing test and a clear return option over a pristine case or original packaging. Ask for a short video showing the tool connected to air, cycling several fasteners into scrap wood, and adjusting depth. This check can reduce uncertainty without requiring a buyer to pay a premium for cosmetic condition.
Local pickup can save $10-$40 in shipping and makes inspection easier. However, travel time should count: a long drive for an untested tool may be less economical than paying for tracked shipping from a seller who accepts returns. Compare the delivered total, not just the listing price.
Buy nails in a box size appropriate to the work rather than stocking several lengths immediately. A 16-gauge box often costs about $10-$35, with longer nails and larger quantities tending toward the high end. Confirm the nail type and length for the SB-1664FN before buying; incompatible fasteners can waste money and cause feeding problems.
When a repair is needed, get a parts and labor estimate before committing. If the expected repair exceeds about $75-$100, compare the repaired total with a tested used unit or a new basic pneumatic model. Do not pay extra for a compressor or hose if those items are already on hand, and avoid buying a bundle that includes equipment the job does not require.
Assumptions: Prices are estimates for U.S. buyers and can vary with condition, seller, shipping, local supply, and parts availability.