Brown Persa granite typically costs $65-$125 per square foot installed, with a 30-square-foot kitchen countertop averaging about $2,850. Slab grade, vein layout, edge details, sink cutouts, local labor, and removal of existing counters can move a quote well outside that estimate.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Installed Brown Persa granite | $65 per sq ft | $95 per sq ft | $125 per sq ft | Stone, standard fabrication, and installation |
| 30-sq-ft countertop project | $1,950 | $2,850 | $3,750 | Before unusual demolition or plumbing work |
| Brown Persa slab material | $40 per sq ft | $60 per sq ft | $85 per sq ft | Price varies by slab grade, thickness, and supplier |
| Fabrication and installation labor | $25 per sq ft | $35 per sq ft | $50 per sq ft | Can rise with complex seams and cutouts |
| Sink cutout | $150 | $250 | $400 | Cutout only; sink and plumbing are separate |
Assumptions: U.S. pricing for standard 3-cm stone, a straightforward kitchen layout, normal access, and a mid-range slab selection. Installed estimates usually include template measurement, fabrication, delivery, and setting the countertop. Confirm whether sales tax, sink removal, backsplash, and sealing are included before comparing quotes.
Brown Persa granite prices for a standard kitchen
Brown Persa is a Brazilian natural stone known for a warm brown base with cream, gray, and sometimes rust-colored movement. Installed prices commonly fall between $65 and $125 per square foot. A typical 30-square-foot kitchen therefore costs roughly $1,950-$3,750, while a 45-square-foot layout may run $2,925-$5,625 before extras.
A practical planning figure is about $95 per square foot installed, or $2,850 for 30 square feet. Lower quotes generally reflect a less costly slab, simple straight runs, standard edges, and minimal waste. Premium slab selection, large islands, bookmatched patterns, or difficult access can push a project above the typical high range.
Installed pricing usually counts the finished countertop area, not necessarily the full slab area purchased. Because slabs have fixed dimensions and fabrication creates offcuts, a small job can have a higher effective price per square foot if the buyer must pay for substantial unused stone. Ask whether the estimate is based on measured countertop area, slab allocation, or a full slab purchase.
For comparison, 2-cm stone may cost less than standard 3-cm material, but it may require a built-up edge or added support. Those adjustments can narrow or erase the initial savings. The fabricator should identify the thickness and edge construction in writing.
Slab, fabrication, and delivery charges in the quote
The slab is only one part of the bill. Fabrication covers cutting the stone to measured dimensions, polishing exposed edges, and making cutouts. Installation includes setting and leveling the pieces and joining seams. A quote with a low stone rate may still be expensive if it excludes templating, delivery, or job-site work.
| Quote component | Typical low | Typical high | What changes the charge |
|---|---|---|---|
| Brown Persa material | $40 per sq ft | $85 per sq ft | Slab quality, thickness, color movement, and supplier |
| Fabrication and edge work | $15 per sq ft | $30 per sq ft | Edge profile, seams, polishing, and layout complexity |
| Installation labor | $10 per sq ft | $20 per sq ft | Travel, stairs, access, leveling, and crew requirements |
| Delivery and handling | $150 per job | $500 per job | Distance, slab handling, and difficult site access |
| Permits or inspection | $0 | $300 | Usually limited to work involving regulated plumbing or remodeling |
Assumptions: Component ranges are broad U.S. estimates and may be bundled into one installed rate. Request an itemized quote so the slab price can be separated from fabrication, handling, and installation. Check whether each line is a fixed charge or a per-square-foot rate.
Granite installers may charge a minimum job fee rather than applying the published square-foot rate to a very small vanity or bar top. Minimums commonly add $300-$800 to small orders, depending on the shop and travel distance. A bathroom vanity with 8 square feet of stone may therefore cost considerably more per square foot than a full kitchen.
Vein layout, thickness, and cutouts change the final price
Brown Persa’s natural pattern makes slab selection especially important. A buyer who wants a particular balance of brown, cream, or gray may need to choose a higher-priced slab or reserve more material than the measured countertop area requires. Matching the visual flow across a seam can also increase fabrication time and material waste.
Layout and slab selection can matter as much as the listed stone rate. A straight countertop with one sink cutout is usually less demanding than an island and several runs that need coordinated pattern placement. Get a slab photo or visit the supplier to approve the actual stone, not just a small sample.
Thickness is another quote variable. Standard 3-cm granite generally needs no plywood build-up for many cabinet installations, while 2-cm stone may need reinforcement or a laminated edge. Depending on the design, support and edge work can add about $10-$25 per linear foot. Confirm that the estimate describes the actual finished edge rather than simply naming a profile.
Each additional cutout or unusual corner adds labor. A second sink cutout may cost $150-$400, while a cooktop opening can add $150-$350. Curved corners, drain grooves, specialty faucet holes, and a full-height stone backsplash are normally priced separately. A 4-inch granite backsplash might add approximately $15-$35 per linear foot, including fabrication and setting.
Island overhangs can require steel supports, particularly when the unsupported projection exceeds about 10-12 inches. Support installation may add $200-$600 or more, depending on span and cabinet construction. Large pieces may also require a larger crew or special handling equipment, which can add several hundred dollars.
Installation labor for seams, edges, and access
A typical kitchen countertop job involves a measurement visit, fabrication, and an installation appointment. After cabinets are ready, installation commonly takes 4-8 hours for a standard kitchen, though larger layouts or multiple pieces can take longer. The full process from final template to installation often takes 1-3 weeks, depending on slab availability and the fabricator’s schedule.
Labor is most predictable when cabinets are level and the layout has few seams or special cuts. Some shops use per-square-foot pricing; others combine labor into an installed rate or charge separately for particular tasks. Where hourly rates are used, skilled stone fabrication or installation labor may run about $50-$100 per hour, but many companies quote the completed job instead.
Example: 8-14 crew-hours at $50-$100 per hour equals $400-$1,400 in labor before shop fabrication, travel, or material costs. This formula is a comparison tool, not a substitute for a project quote, because shops may use crew rates and bundled pricing.
Stairs, narrow hallways, long carries, limited parking, and upper-floor access can increase handling charges by $100-$500 or more. A seam may be needed when a run is longer than the usable slab dimension, and the installer may charge extra for seam placement and color matching. Ask where seams will fall before approving the template.
Three kitchen layouts with realistic Brown Persa quotes
The examples below show how size and scope affect a total. They assume standard 3-cm stone, ordinary cabinet access, and typical U.S. labor. They exclude sales tax, new sinks, plumbing reconnection, and major cabinet repairs.
| Project | Stone area and scope | Approximate rate | Estimated total |
|---|---|---|---|
| Small straight kitchen | 25 sq ft, one sink cutout, eased edge | $75-$100 per sq ft | $1,875-$2,500 |
| Mid-size kitchen | 35 sq ft, sink and cooktop cutouts, two seams | $85-$115 per sq ft | $2,975-$4,025 |
| Kitchen with island | 50 sq ft, island, premium slab selection, support work | $100-$140 per sq ft | $5,000-$7,000 |
Assumptions: The per-square-foot figure reflects the project’s effective installed rate, including normal fabrication and delivery. The island example costs more because slab selection, handling, and overhang support add work beyond its extra square footage.
A 35-square-foot estimate at $3,500 works out to $100 per square foot. If a quote for the same scope is much lower, check for omitted removal, cutouts, edge finishing, or delivery. If it is much higher, ask whether it includes a more expensive slab, full-height backsplash, specialty edges, or difficult access.
Regional granite rates from city to rural markets
Labor and delivery can make Brown Persa granite cost more in major metropolitan areas than in less expensive markets. As a broad comparison, installed prices in high-cost coastal cities may be about 10%-25% above a national midpoint. Mid-sized cities often sit near the midpoint, while some rural markets may be 5%-15% lower if a fabricator is nearby.
Distance to a stone shop can offset lower rural labor rates. A remote delivery, limited installer availability, or a required special trip may add $200-$700. In dense urban areas, parking restrictions, elevator reservations, and building access rules can add handling time even when the fabricator is nearby.
Regional percentages are directional rather than fixed. Two shops in the same city may quote different prices because one stocks Brown Persa slabs locally and another must source them from a distributor. Buyers should compare quotes using the same slab, thickness, measured area, edge, cutouts, and removal scope.
Removal and disposal can add $300 to $1,000
Taking out existing countertops typically costs about $5-$15 per square foot, with a minimum charge often applying to small jobs. A 30-square-foot removal might run $150-$450 for straightforward laminate or tile, but heavier stone, a glued installation, or difficult disposal can bring the total to $300-$1,000. Ask whether the installer will remove the old surface or expects the homeowner to arrange a separate crew.
Sink disconnection and reconnection are commonly separate from stone installation. A plumber may charge roughly $150-$400 to disconnect and reconnect a standard sink and faucet, excluding new fixtures or changes to pipes. Tile backsplash removal can cost another $5-$20 per square foot, especially if drywall repair or wall preparation is needed afterward.
Clarify disposal and plumbing before scheduling demolition. Some countertop shops will haul away the old material for a set fee, while others leave it at the property. A disposal charge of $100-$300 may apply, with higher rates for heavy stone or restricted disposal sites. Cabinet repairs and leveling are also commonly excluded; correcting an uneven base can add $200-$800 depending on the work.
When Brown Persa slab supply affects the price
Natural-stone inventory changes, so the same name does not guarantee identical appearance or price across suppliers. A shop may have a standard-grade slab available at $40-$60 per square foot for the material, while a sought-after lot with more distinctive movement may reach $70-$85 per square foot. Buyers should confirm that the price covers the specific slab being reserved.
Some fabricators require a deposit to reserve a slab or start production. Common deposits range from 25%-50% of the project total, with the balance due at installation or completion. Read the cancellation terms and ask whether the deposit is refundable if the slab has not been cut.
Slab availability matters most when a project has a fixed renovation schedule or requires visual matching. A delayed shipment may postpone templating or installation by days or weeks. If a selected slab is not in local stock, request the supplier’s expected arrival date and determine whether the quote includes freight or a special handling fee.
Price also varies by how the fabricator accounts for remnants. A shop may offer a remnant at a discount for a small vanity or bar, but the piece must be large enough for the required dimensions and its pattern may not match other counters. For a full kitchen, a remnant is rarely a practical substitute for reserving enough slab material.
Lowering the installed price without changing the stone
Keep the countertop outline simple where possible. Straight runs and standard eased edges require less fabrication than curves, multiple cutouts, or elaborate profiles. Choosing a sink and cooktop before templating also prevents costly last-minute changes. Retaining an existing backsplash or using a separate, lower-cost wall finish can avoid paying for additional granite.
The most reliable savings come from reducing fabrication and extra work, not from under-specifying the stone. Compare at least three written quotes using the same Brown Persa slab or grade, thickness, square footage, edge profile, cutouts, removal, delivery, and warranty terms. A difference of $10 per square foot amounts to $350 on a 35-square-foot project.
Ask whether the shop can use a suitable remnant for a small secondary surface, such as a bathroom vanity, while reserving a full slab for the kitchen. Coordinate countertop work with other remodeling tasks when possible, but avoid scheduling the template before cabinets are installed, secured, and level. A measurement taken too early can lead to rework or added charges.
Consider keeping the existing countertop if it is structurally sound and a replacement is being considered only for appearance. Repair may be more economical for a localized chip or seam issue; a stone repair technician may charge about $150-$500 for a small repair, depending on color matching and travel. For replacement, avoid paying for premium edge details or supports that the design does not need, but follow the fabricator’s guidance on thickness and overhang safety.