Continental washing machine prices depend mainly on washer capacity, extraction technology, and installation scope. A commercial unit may cost about $4,000-$28,000 before installation, while a delivered and installed project commonly runs $6,000-$35,000 or more.
Continental Girbau equipment is built for commercial laundry use, so a dependable budget requires a model-specific quote rather than a residential-appliance comparison. Plumbing, electrical work, freight, and site preparation can add substantially to the equipment price.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Commercial washer equipment | $4,000 | $11,000 | $28,000+ | Approximate range by capacity and model type |
| Installed washer project | $6,000 | $16,000 | $35,000+ | Includes typical delivery and installation allowance |
| Equipment per pound of capacity | $150 | $250 | $350+ | Rough comparison metric, not a supplier quote |
| Installation labor | $800 | $2,500 | $7,000+ | Higher when utilities or floors need work |
What Continental commercial washers typically cost
Continental Girbau washer prices are not uniform across dealers, and many commercial models are quoted to order. As a planning range, smaller 20-30 lb units may fall around $4,000-$8,000 for equipment; mid-size 40-60 lb machines often cost $8,000-$16,000; and large 80-100 lb models can reach $16,000-$28,000 or more.
For a typical 40-60 lb washer, an installed budget of roughly $11,000-$21,000 is reasonable when the site already has suitable water, drain, power, and floor capacity. A small replacement in a prepared laundry room may land near the lower end; a new laundromat installation with construction and utility upgrades can exceed the high estimate.
For budgeting, plan around $11,000-$21,000 installed for a mid-size Continental washer at a site with ordinary access and limited construction. These are market-planning estimates, not published Continental list prices; the exact model, dealer discount, freight destination, and project scope change the quote.
Assumptions: U.S. commercial equipment, standard freight access, ordinary installation, and no major building renovation.
How the washer quote divides between equipment and labor
A dealer proposal may combine the machine, freight, installation, and startup into one total. Asking for itemized lines makes it easier to compare bids and identify whether a low equipment price is offset by delivery charges or installation exclusions.
| Quote component | Typical allowance | What changes the amount | Common billing basis |
|---|---|---|---|
| Washer equipment | $4,000-$28,000+ | Capacity, controls, extraction, and model | Per machine |
| Freight and delivery | $300-$1,500 | Distance, liftgate, stairs, and inside placement | Per delivery |
| Installation labor | $800-$4,000 | Utility connections, access, and rigging | $75-$150 per hour or fixed bid |
| Permits and inspections | $100-$1,500 | Local rules and extent of electrical or plumbing work | Per permit or project |
| Removal and disposal | $150-$700 | Old-machine weight and haul distance | Per unit |
Equipment usually represents the largest single line, but building work can push installation above $4,000. A simple changeout may require only a few hours for disconnecting, positioning, anchoring, and reconnection. New drains, upgraded wiring, concrete work, or moving a machine through a tight opening can add several labor days.
Confirm whether the quoted price includes startup, testing, delivery to the final room, hoses, drain fittings, anchors, and removal of the old unit. Those items may be included by one dealer and billed separately by another.
Capacity, extraction, and site work move the estimate
Capacity is a major price driver. A 20-30 lb washer handles smaller daily loads and usually costs less than a 60-100 lb model, but buying too small can require extra cycles and more labor. For a laundromat or institutional laundry, compare pounds per cycle with expected daily volume rather than choosing by purchase price alone.
Extraction design and controls also affect cost. Higher-speed extraction removes more water before drying, which can reduce dryer time, but the machine may require a suitable floor, anchoring, and compatible utilities. A soft-mount model can reduce the need for a special foundation in some installations; a hard-mount washer may need more attention to floor strength and vibration control.
Site conditions can add hundreds or thousands of dollars. A 240-volt circuit or three-phase power requirement, depending on the model, may mean electrical upgrades. Long water or drain runs, a doorway narrower than the machine, stairs, or a floor requiring reinforcement can each change the contractor’s price.
Check the machine’s capacity, voltage, phase, dimensions, and extraction type against the building before accepting a quote. Rework after delivery can be expensive, especially when the machine cannot pass through the intended route or existing utilities do not meet the installation specification.
Assumptions: Capacity bands are approximate; actual specifications and prices depend on the selected Continental model and local dealer.
Three Continental washer quotes for different laundry rooms
The following examples show how equipment price and project scope combine. They are illustrative estimates for commercial projects, not offers for a specific model or dealer inventory.
| Example | Scope and labor | Equipment | Other project charges | Estimated total |
|---|---|---|---|---|
| Small replacement | 25 lb washer, prepared room, 6-8 labor hours | $5,000-$7,000 | $700-$1,500 delivery and setup | $5,700-$8,500 |
| Mid-size laundromat | 50 lb washer, standard connections, 12-18 labor hours | $9,000-$15,000 | $1,500-$4,000 delivery, labor, and disposal | $10,500-$19,000 |
| Large-capacity installation | 90 lb washer, rigging, utility adjustments, 24-40 labor hours | $18,000-$28,000+ | $4,000-$10,000 rigging and site work | $22,000-$38,000+ |
The same brand can produce a wide project range because the room and machine capacity matter as much as the model price. The small replacement assumes clear access and reusable connections. The large installation assumes more complicated handling and possible electrical, plumbing, or floor work.
When comparing estimates, check that each bid uses the same capacity and comparable extraction features. A proposal with a lower total may exclude startup, hauling, or code-required work, making its apparent savings misleading.
Installation time and commercial labor rates
A straightforward washer replacement can take about 4-8 hours of on-site work, often with two technicians for moving and positioning. A new installation commonly takes 1-3 days when plumbing and electrical connections need adjustment. Major construction or difficult rigging can extend the schedule further.
Commercial appliance technicians and tradespeople may charge roughly $75-$150 per hour, with minimum service calls commonly around $150-$400. Specialized rigging, crane service, or after-hours work may be priced as a separate flat charge rather than standard hourly labor.
Ask the dealer to state crew size, estimated labor hours, and what counts as extra work. A fixed installation price can help control the budget, but the contract should list exclusions such as concrete repair, long-distance hauling, utility upgrades, or inaccessible equipment rooms.
Scheduling also affects cost. If the laundry room must remain open, an installer may need to work in stages or outside normal hours. For a multi-machine project, ask whether machines can be installed together to reduce repeated freight, setup, or travel charges.
Continental washer prices by region and delivery distance
Equipment pricing may be similar across many markets, but delivery, dealer availability, labor, and local construction rates create regional differences. As a broad planning adjustment, major metro areas in the Northeast and West Coast may run 10%-25% above a national mid-market installation estimate. Smaller Midwest and Southern markets may be 5%-15% below it when dealers are nearby and labor is available.
Rural locations can still cost more than cities if delivery requires a long route, a special truck, or a technician traveling from another service center. Freight can add roughly $300-$1,500 for a typical delivery and may rise when the machine requires inside placement, a liftgate, or special rigging.
Use regional percentages only as an initial budget adjustment, then request a delivered-and-installed quote for the exact address. Local permit fees and electrical or plumbing requirements should be confirmed separately because they vary by municipality and job scope.
For more accurate bids, provide the machine-room address, doorway and hallway dimensions, floor level, available power, drain location, and whether an old washer needs removal. These details help dealers avoid allowances that later become change orders.
Repair, replacement, and warranty expenses to compare
A repair may cost less than replacing a commercial washer when the machine has a localized fault and the drum, frame, and controls remain serviceable. Diagnostic visits often cost $100-$300, while common repairs may total $250-$1,200. Major motor, bearing, or control-system work can reach $1,500-$4,000 or more, depending on parts availability and labor.
Compare the repair estimate with the price of a replacement and the expected downtime. A machine needing recurring repairs, leaking around a damaged tub, or lacking available parts may justify replacement even if the immediate repair costs less. In contrast, a relatively new unit with one failed valve or door component may be a practical repair candidate.
Warranty coverage can reduce eligible parts expense, but labor, travel, and downtime may not be covered. Confirm the warranty term for the selected model, the party responsible for service, and whether coverage requires installation by an authorized technician. Extended service plans should be compared against expected repair exposure, not treated as an automatic savings.
In a busy laundromat, the cost of lost cycles can matter as much as the invoice. A repair that restores service quickly may be less expensive overall than waiting for a replacement, while a repeated breakdown can make an otherwise low repair quote a poor long-term value.
Lower the Continental washer bill through controlled scope
Start by matching capacity to actual laundry volume. Oversizing raises equipment and utility costs; undersizing may create extra cycles and longer operating hours. Request model options at two adjacent capacities and compare quoted price, cycle throughput, and required power before deciding.
Keep the installation simple where possible. Measure the full delivery path, clear the room before the crew arrives, and verify utility connections with the dealer. Reusing compliant plumbing and electrical service can avoid unnecessary construction, but old connections should not be reused if they fail the manufacturer’s specifications or local code.
Compare complete installed bids rather than choosing the lowest equipment-only price. Ask at least two dealers to itemize freight, setup, startup, removal, permits, and warranty terms. Comparable bids make it easier to see whether one quote includes work another treats as an extra.
For a multi-machine project, ask whether combined delivery or installation reduces per-unit charges. Consider standard features before paying for optional controls or upgrades that do not support the laundry operation. Avoid rushing a replacement unless the machine is unusable; planned purchasing can leave time to compare models and schedule ordinary labor.
Finally, get all assumptions in writing. The quote should identify model and capacity, delivery location, installation boundary, taxes, permit responsibility, disposal, and exclusions. A clear scope helps prevent change orders and makes the final Continental washing machine price more predictable.