A Laundry Jet Plus system typically costs about $3,000-$7,500 installed in a U.S. home, with a straightforward project averaging roughly $5,000. The final price depends on the system package, number and location of inlets, duct route, wall and ceiling access, electrical work, and local installation rates.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Laundry Jet Plus equipment | $2,500 | $3,500 | $4,500 | Package contents and retailer pricing vary |
| Installation labor | $500 | $1,500 | $3,000 | Assumes ordinary residential access |
| Ductwork and fittings | $200 | $600 | $1,200 | Higher for long or concealed runs |
| Typical installed project | $3,000 | $5,000 | $7,500 | Before major remodeling or unusual electrical work |
What Laundry Jet Plus installation typically costs
For budgeting, allow $3,000-$7,500 for a complete Laundry Jet Plus installation. A lower-cost job generally has a short, direct route from the laundry room to the machine, one or a few inlets, accessible framing, and no major finish repair. A project near the upper end may involve several floors, longer duct runs, additional inlet locations, electrical work, and patching or repainting.
The equipment portion is often about $2,500-$4,500, depending on the Plus package, included components, seller, and current promotions. Installation and project materials commonly add $700-$3,000. A quote that lists only the machine may not include ducting, inlet installation, electrical work, delivery, or wall repairs, so the advertised price is not necessarily the installed price.
Per inlet, a rough installed allowance is $300-$900 when the main unit and duct route are already part of the project. This is not a stand-alone rate: adding an inlet in an open wall is less costly than cutting and restoring a finished wall. Assumptions: U.S. residential installation, standard materials, ordinary access, and no major structural changes.
How the Plus unit, ducts, and wall work shape the quote
Contractors may combine parts and labor into a single installed price. The breakdown below helps show whether a quote includes the complete scope. Ask for separate equipment, installation, and finish-work amounts before comparing bids.
| Quote component | Typical range | What changes the amount | Common pricing basis |
|---|---|---|---|
| Laundry Jet Plus equipment | $2,500-$4,500 | Package configuration, included inlets, seller terms | Per system |
| Labor | $500-$3,000 | Access, routing, number of openings, crew time | $75-$150 per hour |
| Ducts and fittings | $200-$1,200 | Run length, bends, diameter, concealed routing | $10-$35 per linear ft plus fittings |
| Electrical work | $150-$600 | Existing outlet, circuit capacity, outlet location | Per connection or electrician visit |
| Wall repair and painting | $150-$1,000 | Number of cuts, wall finish, paint matching | Per opening or small project |
Rates are planning ranges, not a manufacturer price list. A contractor may charge a minimum service fee, bundle electrical work with installation, or exclude finish repair. Delivery, taxes, permits where applicable, and travel may appear as separate line items.
Why duct length, inlet count, and floor layout change price
The most important project variables are the path between the inlets and the central unit, how many inlets are installed, and whether the route passes through finished spaces. More distance and more concealed work usually raise labor and restoration costs faster than the duct material cost alone.
A short route of about 10-20 linear ft through accessible framing may keep duct materials near $200-$500. A 30-60 ft route with several turns or transitions can push ducting and fittings toward $500-$1,200 and require more labor. Exact acceptable routing depends on the system instructions and installer design, so the quote should identify planned lengths and fittings rather than assuming that any path will work.
Each additional inlet can add roughly $300-$900 installed when the central equipment and main route are already included. Two or three convenient inlets may cost less per opening than widely separated inlets that need separate branches. A home with two or more floors may need longer vertical routing, floor penetrations, or access panels; those details can add several hundred dollars or more.
Wall construction matters, too. Open studs during a remodel are usually less expensive to work around than painted drywall, tile, cabinetry, or plaster. Cutting into masonry or a finished ceiling may require specialized labor. Confirm who will patch, texture, and paint openings; many installation quotes cover the mechanical work but leave cosmetic restoration to another trade.
How many installer hours does a typical job require
A simple installation may take one experienced installer or a small crew about 6-10 hours on site. A more involved project with several inlets, long routing, electrical coordination, and finish repairs can require 12-24 labor hours spread across one or more visits. Labor is commonly priced at $75-$150 per hour, although contractors often quote a fixed project amount.
These hours do not always equal elapsed time. A crew may finish the duct and inlet work in a day but return after an electrician, drywall worker, or painter completes a separate task. Before accepting a schedule, ask whether the quote includes layout, installation, cleanup, testing, and a return visit if needed.
Homeowners can check the proposed labor allowance by multiplying estimated hours by the stated hourly rate, then comparing that result with the labor line in the quote. For example, 10-16 labor hours at $90-$130 per hour equals $900-$2,080 before any minimum charges or separate finish work. Planning example: 10-16 labor hours, not a guaranteed installation duration.
When a new Laundry Jet system costs more than alternatives
The Laundry Jet Plus is a built-in laundry transport system, so its price should be compared with the cost of routing laundry by hand, adding a conventional laundry chute, or buying a different system. A low equipment price is not an apples-to-apples comparison if it excludes the duct route, installation, or required accessories.
A basic gravity chute may cost about $500-$2,500 to install where the home layout allows a straight, code-compliant path. However, a chute may not fit the same locations or provide the same transport method, and a new vertical opening can make construction expensive. For a chute that crosses finished floors or needs substantial framing, the full project can exceed $3,000.
Carrying laundry baskets has no installation cost, but it does not provide the convenience of a fixed system. A Laundry Jet project is more likely to make financial sense during new construction or a major renovation, when framing and wall access are already available. For an existing finished home, request a written comparison of the system, duct route, and restoration work before deciding whether installation fits the budget.
How U.S. labor markets affect the installed price
Labor and contractor availability can shift installed pricing substantially. As a planning estimate, a project in a lower-cost rural or small-city market may land about 10%-20% below the national midpoint. Major metropolitan markets and high-cost coastal areas may run 15%-35% above it, particularly when electricians, drywall trades, and specialty installers are billed separately.
Those percentages are approximate, not fixed regional tariffs. Local travel fees, contractor minimums, building access, and whether a qualified installer is nearby can matter more than the state average. A rural homeowner may have lower hourly rates but pay additional travel or scheduling charges, while an urban project may face parking, elevator, or restricted work-hour costs.
For a quote near $5,000, a rough regional comparison could be around $4,000-$4,500 in a lower-rate market and $5,750-$6,750 in a high-rate market, assuming similar scope. Compare bids using the same number of inlets, duct path, electrical allowance, and wall-repair responsibilities.
Which add-ons can push the Laundry Jet Plus budget higher
Additional inlets, difficult access, electrical changes, and restoration are the most common reasons a project exceeds its initial equipment budget. Keep a 10%-15% reserve for concealed conditions when walls or ceilings must be opened.
Typical add-ons include about $300-$900 for each additional inlet on an existing route, $150-$600 for an electrical connection or outlet change, and $150-$1,000 for patching and painting. A longer duct path can add $10-$35 per linear ft for materials, plus the labor to route and secure it. These amounts can rise when the work involves tile, cabinets, plaster, masonry, or difficult attic and crawlspace access.
Permits may not be required for every installation, but local rules can apply if the project changes electrical wiring, penetrates rated assemblies, or involves structural work. Permit and inspection charges vary by jurisdiction; allow roughly $0-$300 for a straightforward scope, while more involved alterations may cost more. Ask the installer to identify any permit requirement instead of assuming it is included.
Check whether the quote includes delivery, tax, system testing, cleanup, and warranty service. A low bid that omits patching, travel, or electrical work can become the most expensive option after add-ons. Have each contractor state what is excluded and how concealed obstructions will be priced.
How to lower the price without cutting useful scope
The most effective savings usually come from choosing the route and timing carefully, not from skipping necessary parts of the installation. Plan inlet locations around a short, accessible duct path before walls are closed or cabinetry is installed.
During new construction or remodeling, coordinate the route with framing, electrical, and drywall work. Open-wall access can reduce labor and patching costs, while adding the system after finishes are complete may require extra visits. Keep the inlet count limited to locations that will be used, and avoid adding distant openings simply because they are possible.
Request at least two or three written quotes with the same equipment package and project details. Ask each bidder to price the system, number of inlets, estimated duct length, electrical work, finish repair, delivery, and taxes separately. A quote that is $500 lower may not be cheaper if it excludes several hundred dollars of restoration or travel charges.
Where possible, arrange related work in one visit and confirm whether the existing electrical setup can be used safely and according to the manufacturer’s requirements. Do not reduce cost by improvising duct sizes, bypassing installation instructions, or leaving openings unfinished. Those shortcuts can compromise operation or create repair expenses that outweigh the initial savings.