Menards treated lumber prices vary by board size, treatment rating, location, and current inventory. Common pressure-treated boards often cost about $5-$20 each, while a small deck or fence can require several hundred dollars in lumber before fasteners, delivery, or labor.
The ranges below are planning estimates, not live Menards quotes; store prices and promotions can change. For a reliable budget, compare the exact length and treatment label at the local store and calculate the full material list.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| 2x4x8 treated board | $5 | $7 | $9 | Typical general-purpose dimensional lumber |
| 2x6x8 treated board | $7 | $10 | $13 | Common for joists and framing |
| 4x4x8 treated post | $10 | $15 | $20 | Price shifts with grade and treatment |
| 5/4x6x8 treated deck board | $7 | $10 | $13 | Nominal sizing; actual dimensions are smaller |
| Small treated-lumber deck package | $700 | $1,400 | $2,500 | Materials for roughly 100-150 sq ft; excludes labor |
What Menards Charges for Common Treated Boards
For everyday projects, a treated 2x4x8 commonly falls around $5-$9, a 2x6x8 around $7-$13, and an 8-foot 4×4 post around $10-$20. Longer boards, heavier dimensions, structural grades, and products intended for ground contact usually cost more. These are approximate shelf-price ranges across U.S. markets, not guaranteed prices at every Menards location.
Decking boards are priced by piece, while project planning is often easier by square foot. A pressure-treated 5/4×6 deck board may run about $1.75-$3.25 per linear foot, or roughly $3.50-$6.50 per sq ft of surface coverage before spacing and waste. Framing lumber adds to that amount. A basic treated deck lumber package commonly works out to about $7-$17 per sq ft, depending on its framing and layout.
Assumptions: standard pressure-treated pine, common 8-foot lengths, ordinary retail availability, and no contractor labor. Menards prices can be affected by local supply, board grade, and promotions. If a store advertises a rebate, check its terms and whether the displayed shelf price already reflects it; a rebate may not lower the upfront amount paid.
Board Dimensions and Grades Behind Menards Shelf Prices
Nominal dimensions do not equal finished dimensions. A nominal 2×4 measures about 1.5 by 3.5 inches, and a 5/4×6 deck board is typically about 1 inch thick and 5.5 inches wide. A larger board contains more wood and generally costs more, but price also depends on length, grade, drying, and intended use.
Ground-contact lumber is treated for exposure where wood touches soil or remains close to it. It generally costs more than lumber labeled for above-ground use. The treatment label and end tag matter more than appearance alone: use the rating specified by the project design, particularly for posts, deck framing close to grade, and fence components in soil.
Longer lengths can reduce joints in a run but may carry a higher total price and be harder to transport. A 12-foot board may cost more than an 8-foot board, though its cost per linear foot may be comparable or lower. Compare price per linear foot as well as price per board when choosing between lengths.
What the Menards Lumber Quote Includes Beyond Boards
A lumber-only estimate can understate the project budget. A deck or fence also needs connectors, compatible fasteners, waste allowance, and possibly delivery or disposal. The table shows common planning ranges; quantities vary with design, local code, and the chosen product.
| Cost component | Typical range | Pricing basis | What changes it | Budget note |
|---|---|---|---|---|
| Treated framing and decking | $7-$17 | Per sq ft of basic deck area | Board size, layout, grade | Does not include labor |
| Fasteners and connectors | $75-$250 | Small-to-medium deck | Joist count, hardware type | Use hardware rated for treated wood |
| Concrete and post base materials | $8-$18 | Per post position | Hole depth, soil, footing design | May not include excavation |
| Delivery | $50-$150 | Per local order | Distance, load, store terms | Confirm minimums and access |
| Waste and cut allowance | $40-$180 | Project allowance | Board lengths and layout | Often budget 5%-10% extra |
Hardware and fasteners should be suitable for contact with pressure-treated lumber because treatment chemicals can corrode incompatible metals. Coated or stainless options may cost more than basic fasteners, but specifying the correct type avoids replacing corroded connections. Small projects may also face minimum delivery charges that make pickup more economical.
For installed work, labor is separate from Menards retail lumber pricing. A contractor may quote labor by the project or charge about $45-$90 per hour, with regional differences and minimum job fees. Use the formula as a rough comparison only; a written quote should state what installation, cleanup, and disposal include.
Deck Size and Treatment Ratings That Move the Quote
Project area is a major driver, but structural layout matters too. A straightforward 10-by-12-foot deck has 120 sq ft of surface; a raised deck with stairs, railings, and extra support can need substantially more lumber and hardware than a ground-level platform of the same area. For a basic treated lumber package, a 120-sq-ft deck might use about $840-$2,040 in lumber before connectors, delivery, or labor.
Joist spacing also changes the material count. Many deck plans use joists at 16 inches on center, while some decking products or designs call for 12 inches. Reducing spacing increases framing lumber and connector quantities, so a 12-inch layout can add roughly 10%-25% to framing material compared with a similar 16-inch layout, depending on dimensions and beam placement.
Posts set in soil or exposed to persistent moisture may require ground-contact treatment, while above-ground framing may use another rating specified by the design. An 8-foot 4×4 ground-contact post can be several dollars more than a comparable above-ground post. Confirm the required treatment level before comparing prices; the cheapest board may not be approved for its intended location.
Site conditions can further change the order. Uneven ground, long stair runs, irregular deck shapes, or a fence line with frequent corners create more cuts and offcuts. For a fence, posts spaced around 6-8 feet apart require different quantities than a layout with closer spacing. Measure actual runs and openings before purchasing rather than estimating from total yard area.
Ways to Trim a Treated-Lumber Bill Without Cutting Corners
Start with a measured cut list that groups pieces by length. Planning around standard 8-, 10-, or 12-foot boards can reduce leftover sections, though the best length depends on the design and what is available locally. Add a modest waste allowance instead of buying an arbitrary extra stack, and keep structural dimensions consistent with the plan.
Compare equivalent products by treatment label, grade, dimensions, and length. A lower shelf price is not a true saving if the board is unsuitable for ground contact or has a different usable size. For visible deck surfaces, compare treated pine with alternatives only after counting the full system; composite decking, for example, has a different upfront price and may not use the same framing package.
Pickup can avoid a delivery fee if a suitable vehicle is available and the boards can be transported safely. For a large order, however, delivery may be cheaper than repeated trips or renting a vehicle. Check the local store’s delivery charge, minimum order, and unloading conditions before choosing.
Ask for itemized quotes from more than one source using the same cut list and treatment requirements. Check whether a quote includes connectors, taxes, delivery, and any rebate assumptions. Keep the design fixed while comparing prices so savings reflect real differences rather than missing materials.
Regional Menards Pricing and Pickup Differences
Retail lumber prices can vary by metro area, shipping distance, local inventory, and regional demand. A practical planning allowance is to expect prices in a higher-cost metro or supply-constrained market to run about 5%-15% above a lower-cost market for comparable treated boards. That is a budgeting range, not a guaranteed Menards regional price schedule.
Weather and construction activity can affect availability. Spring and early summer often bring more demand for deck and fence materials, while a store may have fewer options in less common lengths or treatment ratings. A substitute board can alter both price and project dimensions, so confirm stock for the full list before arranging a pickup or installation date.
Local store inventory is especially important for long boards and bulky orders. A nearby location may not have enough matching pieces, and transfer or delivery availability can change the final cost. Use the chosen store’s current listing or call the lumber desk to verify quantity, length, and treatment before traveling.
Three Menards Treated-Lumber Project Budgets
These examples illustrate material budgets rather than current store quotes. They assume ordinary access, standard pressure-treated lumber, a modest waste allowance, and no structural engineering or unusual ground work. Local prices can fall outside the ranges.
| Project | Material scope | Estimated total | Key assumption |
|---|---|---|---|
| Small deck repair | 8-12 boards, connectors, fasteners | $120-$350 | Replace a limited area; reuse sound framing |
| 10-by-12-foot ground-level deck | Framing, deck boards, basic hardware | $900-$2,300 | 120 sq ft; no railing, stairs, or labor |
| 100-foot privacy fence | Posts, rails, treated boards, concrete | $1,200-$3,200 | About 6-foot post spacing; gate excluded |
The repair example assumes the existing structure is sound and only a few boards need replacement. If rot extends to joists or posts, the scope can expand quickly. The deck example includes typical framing and surface lumber but excludes permits, demolition, railing, and installation. The fence total varies with fence height, board style, corner count, terrain, and post treatment.
Installation can add roughly $15-$40 per sq ft for a straightforward deck, with stairs, railings, elevated construction, and difficult access pushing labor higher. Fence installation may be quoted by linear foot, often around $12-$30 per linear ft for basic wood fencing, excluding unusual site work. Separate the material allowance from labor in any estimate to see which part drives the total.
Delivery, Cutting, and Other Charges to Budget
Menards store services and fees can differ by location. Delivery commonly adds about $50-$150 for a local order, but distance, load size, and access can push the charge outside that range. A delivery estimate should clarify whether the driver unloads at the driveway or places lumber elsewhere; moving materials around a property is not always included.
Ask whether the store offers cutting and what limits apply. Retail cuts may help with transport, but they are not a substitute for a project cut list, and availability can depend on the store and workload. Allow for jobsite trimming because boards may need to be squared or adjusted after measuring actual conditions.
Removal of an old deck or fence is usually a separate contractor expense. Basic demolition and disposal can add several hundred dollars or more, depending on size, access, and whether concrete footings must be removed. Permit fees, inspections, and code-related changes also depend on the municipality; check local requirements before buying materials or starting work.
Pressure-treated lumber should be handled and disposed of according to product labeling and local rules. Budget for gloves, eye protection, and safe storage if these are needed, and avoid burning treated wood. Confirm delivery, disposal, and permit charges separately because they may not appear in a board-price estimate.
Menards Treated Lumber or a Different Material
Pressure-treated pine is often among the lower-cost choices for outdoor framing and decking. Cedar and other naturally durable woods may cost more per board, while composite decking can have a much higher upfront material price but requires a different maintenance plan. Compare the whole installed assembly rather than the surface board alone.
Repairing a damaged section can cost less than replacing a complete deck or fence if the surrounding structure is sound. A few replacement boards may be a $120-$350 material purchase, while widespread rot, loose posts, or deteriorated framing can make a larger rebuild more practical. Have uncertain structural damage assessed before relying on a surface-only repair.
For a quote comparison, list the same board dimensions, treatment rating, length, hardware, and delivery needs for every option. Include expected upkeep and replacement of individual components where relevant. A lower upfront price is useful only if the selected product suits the exposure and project design.