Price Pfister Pfirst Series faucets generally cost about $40-$160 for the fixture, with many common models priced around $70-$100. A professionally installed faucet commonly brings the total to $180-$500, depending on faucet type, local plumbing rates, existing connections, and whether removal or repairs are needed.
The fixture is usually the smaller part of the bill; labor and site conditions drive much of the installed price. The estimates below cover typical U.S. retail and plumbing work, not a guaranteed current price for a specific finish or seller.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Pfirst Series faucet | $40 | $85 | $160 | Fixture only; model and finish affect price |
| Professional installation | $140 | $250 | $450 | Basic replacement labor, before unusual repairs |
| Basic installed total | $180 | $335 | $610 | Faucet, labor, and routine supplies |
| Removal or small repair | $25 | $75 | $200 | Added when old hardware or connections are difficult |
What a Pfirst Series faucet costs by type
Retail pricing varies by seller, finish, included drain parts, and whether a listing is a current model or remaining inventory. A basic bathroom faucet typically falls near the lower end, while a kitchen faucet with a pull-down spray or a less common finish can cost more. The following are planning ranges rather than fixed manufacturer prices.
| Faucet type | Fixture price | Typical installed total | Common scope |
|---|---|---|---|
| Bathroom single-handle | $40-$90 | $180-$380 | Existing sink holes and accessible shutoff valves |
| Bathroom two-handle | $50-$110 | $200-$420 | Two handles; drain assembly may be included or separate |
| Kitchen standard or pull-down | $65-$160 | $220-$500 | Replacement at an existing sink opening |
| Tub or shower trim | $50-$150 | $200-$550 | Trim replacement; valve work can raise the total |
For a straightforward sink-faucet replacement, budgeting $250-$400 is a reasonable midpoint. That estimate assumes a standard Pfirst Series fixture, usable shutoff valves, no countertop changes, and ordinary access. Shower trim pricing is less predictable because some jobs involve only visible trim while others require work on the valve behind the wall.
Assumptions: typical U.S. retail pricing, standard finish, existing compatible plumbing, normal access, and no major plumbing repairs.
How faucet parts and plumber labor shape the quote
A quote can include more than the faucet and a single installation charge. Ask whether it covers removal, supply lines, drain parts, sealant, disposal, and testing. A low labor quote may exclude these items or assume the old faucet comes off easily. Comparing written scopes helps distinguish a genuinely lower price from an estimate that leaves out likely charges.
| Quote item | Typical price | What changes the charge |
|---|---|---|
| Pfirst Series faucet | $40-$160 per unit | Faucet type, finish, seller, and included components |
| Plumber labor | $140-$350 per faucet | Access, removal difficulty, and local hourly rate |
| Supply lines or connectors | $10-$45 per pair | Length, material, and whether old lines can be reused |
| Drain parts or pop-up assembly | $15-$60 per set | Bathroom faucet configuration and included hardware |
| Removal and disposal | $25-$100 | Corrosion, restricted access, and disposal policy |
Plumbers commonly charge about $75-$150 per hour, but many use a minimum service charge or a flat faucet-replacement rate. A visit minimum of roughly $100-$200 may apply even when installation takes less than an hour. For example, 1.5 hours at $100 per hour equals $150 in labor before supplies or a service minimum.
Confirm whether the estimate is a flat installed price or an hourly rate plus materials. Also ask whether the quoted fixture is supplied by the contractor or purchased separately; contractor-supplied products may have a markup, while customer-supplied fixtures may have different labor or warranty terms.
Which Pfirst models and sink layouts change the price?
The faucet configuration determines both fixture cost and installation effort. A single-hole faucet is often simpler to fit than a wide-spread bathroom set, which uses separate handles and a spout. A faucet with a side sprayer, pull-down hose, or separate soap dispenser may require additional openings and connections. The sink or countertop must have compatible holes or a cover plate may be needed.
Bathroom sinks with one, three, or four holes can limit model choices. A faucet designed for a 4-inch centerset layout will not automatically fit a widespread setup with handles 8-16 inches apart. Adapters or deck plates may help with some layouts, typically adding about $10-$40, but they cannot resolve every mismatch. Check the product specifications and measure before buying.
Kitchen faucet reach and height matter too. A tall or pull-down spout may be convenient but can conflict with a low window, cabinet, or shallow sink. A replacement that fits the existing hole pattern usually avoids countertop drilling. If new holes are needed in stone or another hard surface, specialized work can add about $100-$300 or more, depending on material and access.
Compatibility is often the most avoidable source of added expense. Confirm mounting-hole count, faucet reach, supply connection size, and whether a drain assembly is included. For shower trim, identify the existing valve brand and model before ordering; decorative trim is not necessarily interchangeable with another valve body.
Assumptions: existing sink or tub openings remain unchanged; prices for drilling or valve replacement are additional.
How long does Pfirst Series faucet installation take?
A simple bathroom or kitchen faucet replacement often takes a plumber 1-2 hours when the shutoff valves work and the old fixture releases normally. A two-handle faucet, tight cabinet, or separate drain assembly can push the job toward 2-3 hours. Difficult removal, corroded hardware, or a leaking valve can make the visit longer and raise labor charges.
DIY installation can reduce the labor bill, but the savings depend on having the right tools and being able to shut off water reliably. Basic work may require an adjustable wrench, basin wrench, towels, and plumber’s putty or sealant specified by the manufacturer. A damaged supply line or overtightened fitting can lead to a leak under a sink, so the connection should be checked after installation and again after water has run.
Professional installation is more likely to make sense when shutoff valves are seized, the sink cabinet is cramped, or the faucet is part of a larger plumbing repair. A plumber may charge a diagnostic or minimum visit fee even if the replacement itself is quick. Ask whether the quote includes testing for leaks and correcting minor connection issues.
Allow a half-day appointment window even when the hands-on replacement is expected to take less than two hours. Scheduling, access, removal, and parts availability can affect the visit more than the faucet’s installation instructions suggest.
Why Pfirst Series quotes differ across U.S. regions
Labor is usually the largest regional difference. In lower-cost small-town markets, basic replacement labor may be closer to $100-$200 per faucet. In high-cost metro areas, the same scope can reach $250-$450, especially when a contractor’s trip charge or minimum is substantial. These are broad planning ranges; actual rates vary within each state and even between nearby cities.
Urban parking, older housing, and limited access can add time, while rural customers may see higher travel charges or fewer available appointment times. Regional wages, insurance, business overhead, and contractor demand all affect quotes. The faucet’s retail price may be more consistent nationally than the installed total, although sales, shipping, and limited stock can change what a buyer pays.
For example, a $75 faucet with $160 labor and $25 in supplies totals about $260 before tax in a lower-cost market. At $325 labor with the same fixture and supplies, the same straightforward job totals about $425. This comparison assumes the same access and scope; it is not a guarantee that either market will quote those exact amounts.
Compare at least two local estimates using the same fixture and included tasks. A higher quote may include new supply lines, removal, or a service warranty that a lower quote omits. Check the estimate’s labor minimum and trip charge before comparing its headline total.
What removal, repairs, and extras can add
Removing an old faucet can be quick when its mounting nuts are accessible, but rust and mineral buildup can make the work slow. A difficult removal may add $50-$150 in labor; cutting off badly corroded hardware can cost more if access is poor. Replacing flexible supply lines typically adds $10-$45 for parts, plus any additional labor charged by the plumber.
Old shutoff valves are a common issue. If a valve will not close or leaks after being operated, replacing it may add roughly $100-$250 per valve, including labor and parts, depending on access and local rates. A faucet replacement can also uncover a damaged sink, worn drain, or water-damaged cabinet. Those repairs are separate from a routine faucet installation and should be approved before work proceeds.
For bathroom faucets, a new pop-up drain may add $15-$60 in parts and $30-$100 in labor when it is not included or the old assembly is faulty. For kitchen models, a soap dispenser, side sprayer, or extra connection can add $15-$70 per accessory, before installation. A plumber may also charge a disposal fee of about $10-$40.
Request a price for likely add-ons before the faucet is removed. A written quote can state the extra charge for a failed shutoff valve or corroded mounting hardware and require approval before additional work. That makes a basic estimate less likely to turn into an unexpected bill.
Three installed Pfirst Series price examples
These examples show how fixture choice and labor produce different totals. They assume ordinary plumbing access and exclude sales tax, major repairs, and countertop or wall changes. Regional labor rates and the actual Pfirst model can move each estimate up or down.
| Scenario | Fixture and supplies | Labor assumption | Estimated total |
|---|---|---|---|
| Bathroom single-handle swap | $55-$85 faucet; $10-$25 supplies | 1-1.5 hours at $85-$110 per hour | $150-$275 |
| Kitchen pull-down replacement | $90-$150 faucet; $15-$40 supplies | 1.5-2 hours at $100-$140 per hour | $255-$470 |
| Bathroom two-handle with drain | $70-$120 faucet; $20-$60 drain and supplies | 2-3 hours at $100-$150 per hour | $290-$630 |
In the bathroom single-handle example, the low end assumes an easy removal and no service minimum. The high end allows for a longer visit or a local minimum charge. The kitchen example includes a higher fixture allowance for a pull-down model; it does not assume a new hole or a replaced shutoff valve.
Use the examples as quote-checking ranges, not exact bids. If an estimate is substantially higher, look for a specific explanation such as a valve replacement, difficult access, travel charge, or higher-cost metro labor. If it is much lower, verify that removal, supplies, and testing are included.
How to lower the Price Pfister faucet installation bill
Choose a Pfirst Series model that fits the existing sink or countertop holes. Avoiding new drilling, adapters, and layout changes can prevent added labor and specialty work. Compare the faucet’s total package rather than its sticker price: a model that includes the needed deck plate or drain may cost less overall than a cheaper fixture with separately purchased parts.
Before the appointment, clear the cabinet and remove stored items so the plumber can reach the connections. Confirm that the selected faucet is on site and that its instructions and parts are included. These steps do not eliminate the contractor’s minimum charge, but they reduce delays and the chance of a return visit for a missing component.
Request itemized estimates from two or three licensed local plumbers. Ask each to price the same model and state whether the figure includes removal, supply lines, drain hardware, disposal, testing, and tax. If several faucets need replacement, ask whether one visit can cover them all; bundling may reduce repeated trip charges, though the labor per fixture may not fall proportionally.
Finally, avoid replacing a working shutoff valve or adding premium accessories without a clear reason. At the same time, do not reuse a visibly damaged supply line merely to trim a small amount from the quote. The most reliable savings come from matching the faucet to the existing layout and agreeing on the full scope before work starts.