A Red Jacket water pump price search often refers to a Red Jacket submersible turbine pump (STP), which moves gasoline or diesel from an underground storage tank to dispensers. Buyers typically pay $2,000-$5,000 for pump equipment or roughly $4,000-$10,000 for a standard replacement installed; tank depth, horsepower, wiring, and service work change the quote.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| STP equipment | $2,000 | $3,300 | $5,000 | Motor, pump, and standard hardware; configuration varies |
| Installed replacement | $4,000 | $6,500 | $10,000 | Typical accessible tank and limited piping changes |
| Labor | $1,000 | $2,200 | $4,000 | Removal, installation, wiring, and testing |
| Service call | $250 | $450 | $800 | Diagnostic visit; repair parts may be extra |
Assumptions: U.S. commercial fuel site, standard replacement, ordinary access, and no tank excavation or major electrical upgrades.
What a Red Jacket STP costs for a standard tank
For one common single-tank replacement, budget $4,000-$10,000 installed, with about $6,500 typical. Equipment-only quotes commonly run $2,000-$5,000, depending on pump model, horsepower, length, and included accessories. A pump assembly is not a household water-well pump; it is equipment for a regulated fuel-storage system and must match the tank and dispensing setup.
A like-for-like replacement at an accessible station is usually far less than a project that alters the tank, piping, or electrical system. Per dispenser or per tank pricing is not interchangeable: one STP may supply multiple dispensers, while some sites need separate pumps for different products. Confirm whether a quote covers one tank, one product line, and commissioning.
How motor, labor, and controls shape the quote
Equipment may account for roughly 40%-60% of a standard replacement estimate. Labor reflects fuel-system expertise, site safety requirements, and time needed to remove and test the assembly. The table gives planning ranges, not a fixed parts catalog price; exact model availability and supplier pricing should be checked against the site specifications.
| Quote component | Typical range | What it covers | Cost detail |
|---|---|---|---|
| Pump and motor | $1,700-$4,200 | STP assembly matched to tank and flow | Model and horsepower drive price |
| Accessories and wiring | $200-$900 | Adapters, seals, cable, and small parts | Reuse can reduce materials |
| Removal and installation | $1,000-$3,000 | Qualified technician and lifting equipment | Often 6-12 labor hours |
| Testing and startup | $300-$900 | Electrical checks, leak checks, and functional test | May be bundled with labor |
| Disposal or site work | $150-$1,500 | Old equipment handling or access work | Fuel handling rules affect scope |
For example, 8-12 hours at $125-$225 per hour yields $1,000-$2,700 in labor before travel, equipment, or after-hours charges.
Ask for separate equipment, labor, testing, and disposal lines so a low parts quote is not mistaken for the installed price.
Tank depth, horsepower, and piping that raise prices
Tank geometry and pump length matter: a deeper tank or unusual riser can require a longer assembly or added fittings. A 1-hp unit may suit a modest demand setup, while higher flow needs or long piping runs can call for a larger motor and compatible controls. Moving from a basic configuration to a higher-capacity model can add several hundred to more than $1,500 in equipment and related electrical work.
Site conditions also affect the labor total. Corroded wiring, damaged risers, difficult manway access, or a need to isolate multiple product lines can add $500-$2,500 or more. If the work expands to tank repairs, excavation, or replacement of underground piping, the cost can exceed the standard pump replacement range substantially.
Confirm tank depth, product type, required flow, voltage, and existing piping before approving a model or fixed quote.
How many technician hours a pump swap requires
A straightforward replacement often takes one qualified technician crew about 6-12 hours on site, including removal, installation, electrical checks, and startup. Difficult access, stuck fittings, contamination concerns, or multiple pump units can extend the job to 1-2 days. Commercial fuel work may require scheduled shutdowns and coordination with station staff, which can add mobilization or overtime fees.
Rates commonly fall around $125-$225 per technician hour, though specialist contractors and emergency calls may charge more. A service visit for troubleshooting generally costs $250-$800 before parts. Compare the included hours and crew size, not just the contractor’s hourly rate.
Why regional labor and emergency timing shift totals
Pricing can vary by about 10%-20% between lower-cost rural markets and major metro areas, where specialist labor, travel, and business overhead are higher. Remote locations may also pay more for freight or contractor mobilization. These differences are estimates rather than a guaranteed regional price schedule.
Planned work during ordinary business hours usually avoids emergency premiums. A failed pump that stops sales may require nights, weekends, or expedited parts; expect a possible 15%-40% increase in labor or dispatch charges. Scheduling a replacement before a complete failure can reduce urgency-related fees.
When diagnostics, wiring, or removal add another charge
A pump that hums, trips a breaker, or delivers weak flow may have a motor failure, but wiring, controls, filters, or a leak can produce similar symptoms. Diagnostic work typically costs $250-$800, and replacement components may add $100-$1,000. A new control box, electrical circuit, or longer cable run can add roughly $500-$2,000 depending on distance and site requirements.
Removal and disposal may be included in an installation quote or itemized separately at $150-$1,500. Ask whether fuel recovery, safe handling, testing, and cleanup are included, and whether the contractor has allowed for damaged seals or fittings. A written scope helps distinguish necessary work from optional upgrades.
Repairing a Red Jacket pump versus replacing the assembly
When the fault is a replaceable electrical or control component, a repair may cost $300-$1,500 including diagnosis and labor. A motor or pump assembly replacement is more likely to land in the $4,000-$10,000 installed range. The cheaper repair is not always economical if the unit is repeatedly failing, parts are unavailable, or the tank setup requires extensive labor each time.
Ask the contractor to identify the failed component and state whether repair includes testing and a parts warranty. Compare the repair estimate with the full replacement scope and the age and service history of the pump. Choose repair only when the fault is verified and the expected service life justifies the expense.
Ways to lower the installed Red Jacket pump price
Provide the contractor with tank depth, pump model, motor voltage, product type, and photos of the access area before requesting quotes. This reduces model mismatches and surprise trips. Obtain at least two itemized bids that use the same scope, and ask whether standard parts can be reused safely rather than replaced automatically.
Schedule non-emergency work, bundle service across tanks when practical, and avoid upgrading horsepower or controls without a documented flow or code need. Do not reduce cost by skipping qualified installation, required testing, or applicable fire and environmental rules. The best savings usually come from accurate specifications and controlling added scope, not from choosing an incompatible pump.