A Stihl TS 700 concrete saw typically costs about $1,200-$1,700 for new-old-stock equipment, while used saws often list for $450-$1,000, depending on condition and included parts. Blade choice, shipping, local availability, service needs, and whether the saw is sold as a powerhead or ready-to-cut package can change the final bill.
| Item | Low | Average | High | Notes |
|---|---|---|---|---|
| Used TS 700 powerhead | $450 | $725 | $1,000 | Working saw; condition and service history vary |
| New-old-stock powerhead | $1,200 | $1,450 | $1,700 | Availability is limited; confirm warranty terms |
| 14-inch diamond blade | $100 | $250 | $450 | Price depends on blade type and intended material |
| Ready-to-cut purchase | $600 | $1,000 | $2,100 | Used or new-old-stock saw plus blade and basic supplies |
What a Stihl TS 700 Concrete Saw Costs to Buy
The TS 700 is a gas-powered cut-off saw with a 14-inch cutting wheel. It is an older Stihl model, so prices are shaped by remaining dealer inventory and the used-equipment market rather than a consistent current retail price. A realistic budget is $1,200-$1,700 for new-old-stock or $450-$1,000 for a used saw.
Those totals generally refer to the saw itself, not every item needed to start cutting. Many listings exclude a diamond blade, spare filters, fuel mix, delivery, or a recent service. A used unit near the low end may need maintenance before dependable work; a clean saw with tested compression and documented service tends to cost more.
For a working budget, allow another $100-$450 for a suitable 14-inch blade and roughly $30-$100 for basic consumables or small parts. Sales tax and shipping can add further charges. Assumptions: U.S. pricing, standard 14-inch configuration, ordinary access to parts, and no major engine repair.
How the TS 700 Quote Splits Between Saw, Blade, and Service
When comparing offers, separate the machine price from the equipment and work needed to put it into service. A seller may describe a saw as complete even when the blade is worn, unsuitable for the material, or not included. A dealer’s inspection or repair charge can also change the value of a used unit.
| Quote item | Typical price | What changes the charge | Budget note |
|---|---|---|---|
| TS 700 powerhead | $450-$1,700 | Used condition, inventory, included warranty | Largest share of the purchase |
| 14-inch diamond blade | $100-$450 | Concrete, asphalt, reinforced material, blade grade | Check that the arbor and application match |
| Dealer inspection or tune-up | $75-$250 | Hourly shop rate and repair scope | Ask whether parts are additional |
| Common wear parts | $20-$150 | Filters, belt, starter parts, guards, hoses | Not a full engine rebuild |
| Shipping or local delivery | $0-$150 | Distance, packaging, seller terms | Heavy equipment may cost more to ship |
Repair shops commonly charge around $75-$125 per labor hour, though rates vary by location and shop. A routine inspection can take about 1-2 hours if no difficult faults are found. Ask for a written breakdown of machine price, blade, inspection, parts, and delivery.
Why Blade Diameter, Engine Condition, and Stock Change the Price
Model condition matters more than appearance alone. A saw that starts easily but has low compression, fuel-system trouble, or a damaged belt can require costly work. Before buying used, request a cold-start demonstration and ask whether the seller can provide service records or a shop inspection.
The TS 700’s 14-inch wheel size affects blade replacement cost and cutting depth. General-purpose diamond blades may fall around $100-$250, while higher-grade blades for demanding concrete or reinforced work can run $250-$450 or more. Blade selection should match the material and saw configuration; a low-priced blade is not a good value if it is unsuitable for the job.
Scarce new-old-stock inventory also creates a wide spread. A dealer with one remaining unit may charge more than a private seller, and the warranty may differ from coverage on a current model. A price above $1,700 should be compared against a newer equivalent, especially after adding the blade and delivery.
Repair scope can make a used saw a bargain or a liability. A $600 unit needing a $200 tune-up may still be economical, but a compression problem or major engine repair can push the total beyond the value of a better-maintained machine. Use verified operating condition and included equipment—not listing photos—as the basis for the quote.
How Used TS 700 Condition Raises Repair and Labor Charges
Small, straightforward service may take about 1-2 shop hours, or roughly $75-$250 at common independent-shop rates before parts. More involved fuel, ignition, or starting-system troubleshooting can take 2-4 hours, making labor about $150-$500. These are planning ranges, not a diagnosis; a shop must inspect the saw to quote accurately.
Check the air filter and housing, starter action, throttle response, blade guard, belt condition, water connection, and visible cracks or damage. Ask the shop to distinguish required safety repairs from optional preventive replacement. A repair estimate that approaches $400-$600 deserves comparison with another used saw or a newer model.
A dealer inspection can reduce uncertainty, but it does not automatically guarantee long-term reliability. Confirm exactly what was tested, which parts were replaced, and whether the work carries a parts or labor warranty. Budget repair labor separately from the purchase price so a low listing does not disguise a high ready-to-work cost.
New-Old-Stock, Used, and Newer Cut-Off Saw Prices Compared
Used TS 700s are usually the lowest-cost path, with many asking prices around $450-$1,000. This range suits buyers who can inspect the machine or accept repair risk. A unit with a verified start, sound blade guard, and recent service can command a premium over an untested private-sale saw.
New-old-stock examples may run $1,200-$1,700 before blade and delivery. They may have little operating wear, but age in storage and limited availability still matter. Ask whether the dealer has started and inspected the saw, what warranty applies, and whether the sale includes a blade.
A current or newer equivalent gas cut-off saw can cost roughly $1,300-$2,000 for the powerhead, depending on brand, configuration, and dealer. That comparison is useful when a TS 700 listing exceeds $1,500 or lacks warranty coverage. Compare the total equipped price and support terms, not just the model’s advertised machine price.
Where U.S. Location and Shipping Affect TS 700 Pricing
Prices can vary by roughly 5%-15% between markets because of dealer availability, local labor rates, and demand for construction equipment. Large metro areas may have more sellers and service shops, but higher shop rates. Rural buyers may find fewer local listings and face added travel or freight charges to inspect or collect a saw.
Shipping a heavy, fuel-powered tool may cost about $50-$150 within a typical domestic transaction, depending on distance and carrier requirements. Some sellers will not ship equipment that contains fuel, and packaging or freight arrangements can add cost. A local pickup can save delivery expense but should not replace a cold-start test and careful inspection.
Sales tax depends on the destination and transaction type. For a $1,450 purchase, a 6%-10% tax rate adds about $87-$145. Private-sale tax treatment can differ by state, so buyers should check local rules rather than assuming a listing’s price is the final out-of-pocket amount. Include tax, transport, and any inspection travel in the comparison total.
Which TS 700 Add-Ons Are Necessary for the Cutting Job
A blade is the main add-on, but the right type depends on what is being cut. A general concrete blade may cost about $100-$250, while premium options for reinforced concrete or frequent professional use can reach $250-$450. Confirm wheel diameter, arbor compatibility, and the manufacturer’s guidance before purchase.
Water-feed components, if needed for the work and supported by the setup, may involve roughly $20-$100 in hoses or fittings. Personal protective equipment is a separate job expense: allow around $50-$200 for basic replacement items such as eye, hearing, respiratory, and hand protection if suitable equipment is not already available. Requirements depend on the worksite and cutting method.
Used equipment may also need a belt, filter, spark plug, or starter repair. Minor parts can total $20-$150, while a major repair needs a shop estimate. Do not count optional accessories as required until the intended cut, site rules, and saw configuration are known. Price only the blade and accessories that match the planned material and work method.
How to Lower the TS 700 Purchase Total Without Skipping Checks
Compare at least three offers using the same checklist: running condition, blade inclusion, service history, warranty, and delivery. A $900 saw with a worn blade and overdue service may cost more to prepare than a $1,050 inspected unit that includes a usable blade. Request a video of a cold start when an in-person inspection is not practical.
Set a maximum all-in price before negotiating. Add machine price, estimated tax, shipping, inspection, immediate repairs, and the blade. If that total approaches the cost of a newer saw with dealer support, compare both options rather than stretching the budget for a discontinued model.
For used equipment, ask whether the seller will allow a shop inspection or reduce the price to reflect identified repairs. Avoid paying for accessories that are not needed, but do not omit a suitable blade or safety equipment from the working budget. The most reliable savings come from controlling the total equipped cost, not choosing the lowest unverified listing.